Anyone know if running a blow off with c2 software will cause any problems? ??? Its a vr6 with 268 cams. Thanks

Hey all, I just got my lugtronic setup and I am going to just 86 all the crap of intake issues I had with the 4" MAF, MAF Sensor, tubing, ells...

I thought this was fitting for this section. I have been posting the build thread in the 2.5 section, but I was finally able to start the car for the...

I want to make 300-400 hp and I would prefer not to lower compression. I cannot decide what engine management to use. I am hoping to hear if anybody...

People, and especially people with experience. I'm very doubting about the inlet for my vrt project. I'm running a GT3076R on a stock vr6 but i...

I'm getting a small and normal amount of oil blowby dribbling down my intake from the cold side of my turbo. The filter is at the lowest point so it...

just bought a mk1 with an obd1 ABA turbo setup. It doesn't have an oil pressure gauge. I'm wanting to run the VDO gauge to match the rest, but not...

so im on my second dead maf in <500miles. i have a 12v vr6 with a vortec v9 stage 3 charger kit running c2 #42 software and 4" maf housing. i just...

hey guys idk if im in the right section or not but here we go. ive got a 06 Jetta GLI with the stock turbo. i bought a Garret AIResearch T04 turbo...

alright guys here is the situation i have this downpipe ...

Hi everyone I got a obd2 vrt that I'm havin some mind boggling issues with, had this car for 4 years and never had any issues with it till I turbo'd...

I need help im building a 2.0 turbo but need help with the oil feed line where do i install it?? My oil pan has the oil return line but not the feed...

I already have the tru boost setup but looking to move it to a better location away from the turbo towards the passengers side firewall. Does anyone...

Ok so I'm building a mk4 12v turbo gt35r... What I wanna know is what injectors are you guys having the best results with since the motor is not a...

Hi all - in my setup, I had originally wanted to run a euro GTI oil cooler. BUt with all the added engine bay stuff, the only place to mount the...

Im looking to see if anyone produces a EIP STYLE VR6 turbo manifold. The one that mounts to stock downpipe. Id like to know where you got it...

http://www.youtube.com/watch?v=ensLFDoEeWM&feature=youtu.be it will load up eventually and die out then have to mess with the throttle till you can...

Building a mk1 gti 1.8t project. I am nearly at the point of firing it up but got to figure out my intercooler and piping before i get to that point....

Linden VW in N.J. has a Motorsport Division that carries a full line of HPA parts as well as other major brands. My car was at APR Stage II, having...

We have a Borgwarner EFR 7064-.83 WG in stock ready to ship out, brand new in the box. ...

Does anyone know which wire I should tap into for use as my switch wire (it will tell the 034 relay panel when to turn on and off)? Is there an...

I was driving with my car to tune my VE tables, brand new LC-1 is wired as per manual, good grounds, gauge reads ok, all of a sudden it reads 22AFR...

im coming to you mk3 vrt guys for some suggestions on a good clutch kit. im going to be pushing about 20psi and not going to be dailying it, only on...

Ordered a k04 turbo to upgrade my current k03s turbo. I noticed that the k03s has a bigger compressor wheel, but the k04 has a bigger turbine...

First of all... is this t04 on center? http://i307.photobucket.com/albums/nn299/leperkuan/IMG_20130408_174743_001.jpg Second.. will it fit? ...

I am fabricating my intake/MAF and had a few questions: Is there a way to use a braided stainless steel line for the routing from the DV to the...

Ok, so what I am looking to do is turbo my aba for daily use- just want a little more pep. I was thinking about AHU turbo, manifold, downpipe......

so i bought a kinetic t3/t4 60 trim turbo off a member here, was told it had 5k miles and had no shaft play. thing is toast and needs a full...

While attempting to load my car onto a trailer this weekend, the fuel lines got snagged, pinched and eventually broke loose. The worst part is where...

Hi people , i bought this car : http://www.gumtree.com/p/cars-vans-m...650/1015720624 lots of work had been done to it , like entire new front...