hey guys, im looking for a 50 trim to put on my 1.8t. i definetly want a precision, but not quite sure what to get. im not looking for a highway...

I am looking for a USRT or another brand of inline fuel pump harness for the engine bay so I can hook up my Walbro Fuel Pump. If anyone has a spare...

Guys, I got a buddy's Corrado 16V Turbo and its not firing on 1 and 4. ABA bottom end 16 valve head C2 motor sport chip 440CC injectors I am...

Hey guys, just got a quick question for ya. I just ordered a brand new walbro to replace my old one that no longer pumps. My question is, has anyone...

what should my a/f be at, at idle because mine seems to be between 13.0 and all the way leaned out... what would casue this? set up is pretty much...

I am fabricating my intake/MAF and had a few questions: Is there a way to use a braided stainless steel line for the routing from the DV to the...

Take a good look at the LRI, I am having fabricated. *Long runners similar to the USRT unit I could not afford. *This should really wake up my Built...

http://i47.tinypic.com/2e57cd0.jpg this is the manifold i have SPA from blackforest industries. the turbo i have is the SPA 50 trim from...

i bought an AEM UEGO wideband for my 16vT and im wondering how close to the turbo is too close? theres a threaded plug pretty close to the hotside on...

does anybody have a normal running obd1 vrt? if so i have a couple questions in regards to the egr setup

2002 Mk4 - APR intake, full 3in exhaust, BorgWarner bolt on turbo, FMIC History- ECU with APR stage 1+ had IMMO tripped during Air ride install...

Hello all. This is my first post on the vortex. I am currently putting together my turbo build for my 12v vr6 mk4 jetta. I have almost everything set...

So I have read up about compound turbo setups and sequential turbo setups, now I was wondering if it would be possible to daisy chain a smaller turbo...

All pics can be found here: https://plus.google.com/photos/102391619278461274652/albums/5074139964377177201?banner=pwa&authkey=CLLQuM2wwNflnQE ...

I recently turboed by vr6. I am running 262 cams right now that need to be replaced. Any suggestions on what brand and degree I should go with next?...

I have a 92 gti 16v and was thinking about dropping a turbo into it but I was wondering if anyone could give me any advice in what to do or what...

Hey guys.. been reading and searching alot and still can't make my mind...what do you guys think. I'm looking for the best way to route my feed...

Ok, so I though I had the issue resolved about the smoking at idle, but it seems it's not. 0.60" restrictor, the oil return is big, so no issues...

Greetings, I need some help. Just got a 02 Audi A4 and I am in lOVE with this car so far stock. I'm interested in adding a turbo to it in the near...

So I'm going to get one of those new south gauge pods for my mk2. It houses three guages, I already have wideband to go In, obviously I need a boost...

What frount mount will fit best with a r32 bumper (as far as cutout fitment goes). I just wanna get that nice look of the piping sitting right in the...

Hi there. I searched but cannot find instructions or DIY for how to adjust the belt on an R32 VF supercharger. My belt squeaks a lot for a few...

http://i226.photobucket.com/albums/dd25/issamabed/INAEngineeringLogo-NEW.jpg *** 2.8 12V | 2.8 / 3.2 24V | 3.6 24V VR6 - FLUIDAMPR Pulley *** ...

http://i6.photobucket.com/albums/y217/badboyr66/Jetta/DSCN3315_zps4c5d1c62.jpg I got the head off cause I had a little contamination in my coolant....

http://i6.photobucket.com/albums/y217/badboyr66/Jetta/DSCN3284_zps3664afe9.jpg...

I have just got hold of a precision 6176s turbo and would like to know what size oil restrictor would you recommend using? As I'm not looking to blow...