<center><IMG SRC="http://www.mjmautohaus.com/images/1/eBayBrakingBann.jpg" BORDER="0"></center> <p> MJM Autohaus, a Master Warehouse Distributor...

Alright this is my first post on this forum. im replacing my Master Brake Cylinder in my 1994 Jetta gl 2.0 . so i went to replace the MBC after i got...

MJM doesn't have em, and ecstuning's price seems outrageous. Any other suggestions?

Hi. I have two snapped ebrake or parking brake cables on my Passat wagon. Ordered the new cables from dealer and will receive tomorrow. There is a...

OK, after 53,000 miles on CC, one front disc started to vibrate. Wear is fine, but vibration is horrible. So I need new rotors and pads as well as...

My car is a 06 Jetta TDI. Both front rotors look like this on the outside only. The inside pad contacts like it should, but both outside pads are not...

I just upgraded the front brakes to 10.1" and installed a known working 24.5mm master cylinder into my 1990 Jetta. Pressure bled the system and it...

Try to get the ABS system on my SLC operational again. Here is what I have done so far. 1) Checked ABS codes. Required front wheel sensors to be...

I replaced my ABS control module with one I bought used. I bled the brakes and slave cylinder and went to cycle the "new" control module I put in...

I've always had this issue, both front discs are braking from the lower part of the inside of the front discs. I've changed discs and pads and I...

Has anyone replaced their master cylinder with an aftermarket one? I was looking on germanautoparts.com and they have an aftermarket one for half...

I completed an HPDE yesterday in my Mk1 Audi TT Quattro. This car has 996 4 piston calipers on stock 12.3" discs with Hawk HPS pads and SS lines up...

Fixin' my Ma's brakes tomorrow, not even sure if it's the front, or rear or what. Never even been near the brakes of a MK3, let alone a MK3.5. Not...

http://www.ecstuning.com/sales/ecs600header.jpg Click HERE to order or for more information. EBC Performance Brake Pads For Your Volkswagen -...

With the success of our 6-Piston Front Brake Kit released last year, HPA is proud to announce the release of our 4-Piston Rear Brake Kit for VW...

Please go to this post to answer. Thanks!

Please go to this post to answer. Thanks!

We just did the brakes on my daughters 1988 Cabriolet, the fronts went great (new pads and rotors) but the rear shoes were a challenge. We finally...

HPA is pleased to offer its High Performance 6-piston Big Brake Kit for Mk5/Mk6 VW and Audi TT/A3 applications. The HPA BBK is designed in...

2005 mk4 gti ABS. i've removed my ABS module and master cylinder, and now i'm faced with the problem of bleeding my brakes. research tells me i...

Looking to swap out my front rotors and pads on my b6 passat to improve braking and get rid of some perceived rotor warpage when braking. I am...

Well I installed an RS4 8pot brake kit after bleeding the brakes everything was ok and actually still had a good feel to the pedal and it wasn’t...

Hi all, I have a Corrado SLC. I am attempting to install DE (288mm) brakes on it. Here is what I have: New calipers New carriers New...

I have a 1987 16v GTI that I want to install 1991 Passat 16v hubs to install 10.1 brakes, do I need the axles , tie rods and control arms too or will...

When I'm at a stop, the brake pedal vibrates/shakes... any ideas of what it could be?

http://www.goapr.com/news/wp-content/uploads/2013/05/sowo-2013.png APR is a proud sponsor of Southern Worthersee in Helen Georgia and will be on...

I leaned from this forum regarding brake caliper piston could not pushed back during pad replacement. I just want to share my own experience so that...

https://www.youtube.com/watch?v=aVCsJsZu8RM&feature=youtube_gdata_player The video shows the clicks that I get between 10km/h and 0. Any ideas?

Bentley says "with a full tank of gas" to perform the following Observe valve while a helper pushes the brake and releases quickly. Bentley says...

Ok I have a 1994 mk3 golf, with a 1.8 engine, from the factory it had drums at the back and 239mm solids on the front, so I have set about doing a...