Since there are a lot of new 16v turbo projects being built/rebuilt and some new parts coming out it's time for another ultimate 16vt info thread...

So slow at work. Post up threads on and car engine rebuild...good time to research and learn for my next 16v build!

Block is a 91 2.0 9A, miles unknown. Head is the original one from my 92 2.0 GLi. I plan on this taking awhile....3 kids, full time job,...

Here is what I got in from GAP. Quality gasket for the upper 50mm 16v plenum. They had a small (50) batch shipped from Europe. I didn't want to...

hey guys i just bough motor 9a motor and i break down parts for rebuild and how u guys take off cis fuel line? i don't wanna break it because i want...

will 9A oil pump fit+work in PL/KR block ?

hey there i bought a rocco and im looking to do a turbo set up i would like to know what my options are powerwise boosting through the cis-e system,...

Ive searched all around my local area and am not finding any VW 16v heads and want to know if I could be looking for any audi or volvo 16v heads,...

So I finally get this damn car running going about 30mph is cut off... Checked the fuses fuel pump fuse was shot replaced it now it continues to blow...

Hi all, I don't post much in this forum, but I frequent it from time to time, and some of you may know me from the other forums. Anyway, here is...

As the title states, the website seems to be down<br>Is it up under a different name?<br>Is the information that was on the site saves...

1990 mk2 gli... Car is running and idles good but when I step on the accelerator it wants to die out and sometimes does... Any ideas?!

so, I've been kicking this idea around for a year or so, lurking, looking for a deal; got the 42mm plate itbs for $43 shipped, the manifold for $40...

So i am attempting to replace my timing belt and water pump on my 89 mk2 1.8 16v. I alligned the cam shaft to top dead center, but did not pay...

Looks like the same spec sensor as the oil sending unit? Very high reading compared to factory unit, used to just be above 1/4 now I am seeing...

What do I need for this set up meaning parts ext. also do I need to change my ecu and is it a plug and play set up? Just help me figure it out thanks...

1990 jetta 2.0 engine went out so swapped a decent replacement.. Now new engine will crank but not turn over initially it did run but only for a...

so my vacation is outta the way..not its time to find a 16v engine to tear down. Im planning on putting the bbm g60 kit on a 2.0 16v to go in to a...

1990 gli mk2 running hot after new engine install fans won't kick on at all car seems to be boiling over.... Fans do however kick on after car is...

Hi, 16V Swapped MK1 pickup running fuel injection/digi2 Had the car running about 2 weeks, was sitting at a red light and the car died, limped...

Ok you rare parts hoarders, I really need one of these. Please PM me with what you have. As the title states. I am in need of an big bore throttle...

I'm thinking between NGK (blue) and AUTOTECH 10.4mm (red). for my 2.0 16V (turbocharged, running 43psi boost + nitrous). yes, still running on...

Hi all, looking for somewhere online to source these for my 9a. Only place I found is world implex, about 8 bucks a piece. Anyone know anywhere else...

ive got my replacement on the bench, its a 1.8. should i port and polish it or just leave it. the ports seem pretty clean as far as casting quality...

So the breather hose has the small section, with the restrictor in it...How do you put a catch can inline in the breather hose, without getting rid...

Hey guys, I have an '82 cabby that was originally carbureted. In reading about 16v swaps with cabby's they same fairly straight-forward but those...

Hey guys. I'm ordering new plug wires for the 16v. While shopping around, I noticed that I can buy plug wires with or without an RPM pick up...

I have been reading a lot of horror stories from 16v builds that went wrong...either a machine shop mistake or a random small issue. I have also...

I am trying to get my crank fire setup rocking on my carbed 16V. It's an Electromotive HPV-1. The book says it uses "late model GM ends" The plug...

Did a search, didn't see anything useful... My exhaust was so hot it melted the brand new shift linkage "golf ball " I'm curious as to what...