Did a search, didn't see anything useful... My exhaust was so hot it melted the brand new shift linkage "golf ball " I'm curious as to what...

So, I try to bring my 9a back to life after about 8 months of sitting. Here are the 2 big problems im dealing with, both my fault, and hopefully not...

this is my 3.6 32v v8...16v's seem the best place for me....:D started this idea about a month ago........

Is there a way to do it? I've done a few searches and found nothing. Any input appreciated as always.<p>My engine can take the higher revs, so I'd...

So I bought a car from a guy, cannot get in contact with him. I bought it as a small project. He says the engine runs great, but conveniently the...

If I swap digi 1 in place of the Motronic can I use the stock g60 chip or do I need to buy one? This is a stock 2.0 16v.

Swapping serp stuff from pg block to 9A. I used ABA alt set up on NA pg with stock two piece g60 pulley. Want to use this on stock 16v, is it just...

i recently acquired a head to put on my 2.0, the cams in it have odd stamps. the head is supposed to be off a sirocco, and i didnt check the part...

hey folks, I'm am building up a track car, mk3 aba16vt syncro. for reasons I will not get into here because it will distract from the purpose of the...

I've been out of the game for a little while, but upon cleaning my garage I found enough stuff to rebuild some 16v distributors with new seals and...

Mk1 Scirocco with 2.0 16v swap. Has anyone used the A2 manifold and injection in a A1 swap? If so, what are you using for an intake boot and tube? ...

I am getting this noise when I am cruising at a decent speed. It sounds like the engine/exhaust making the noise and it slowly increases/decreases...

engine came out of my old 1989 Gti 16v. it has sat for the last 4 years in the garage, before it was removed it ran fine the few times i drove it...

Wish I had an extra 12,500 Euros sitting around. ...

I'm kind of confused with this hall sensor and stuff. How would the need to be wired to do?

Are there any oversized valves that are interchangeable with stock 16v valves? I don't mean from other VAG engines, but from other engines entirely?...

This is my first EMS installation. More pictures will be coming soon but this is what the motor looked like before the project. ...

Update - 16V Engine & Trans are installed, time for the external bolt on's. I am so close to being finished with stuff that has to be cleaned and...

Hey had some questions as to what's needed for the swap from a CE1 8v to a 2.0 16v. I will apologize in advance if I've missed any similar threads...

I am looking to purchase an '88 jetta converted to digifant 2. The car does not run and has been having issues since the current owner purchased. He...

I recently just started working on my 1990 2.0 16v after it was sitting for 4 years. it was running rough but it was running. i cleaned up some...

I feel like I was just reading a great thread all about headgaskets and compression for 16vt's but now I can't find it. Here's where I'm at: ...

I drive a 1992 16v Gti purchased it bout 5 months ago. car never gave me any problems what's so ever. Just last night after leaving work I went to...

hey guys just had a quick question. i picked up a spare 2.0 16v motor and im sending im some parts to get powder coated i was curios if there would...

I am putting together a well built 16vt for my caddy. Rods, pistons, bored, etc. Nothing in the engine is stock except the crank. I have a t3/t4...

Hey I just finished swapping in the 16V and the car will turn over and crank, sort of. It will run for about 30 seconds only if I have the throttle...

what's up guys... i'll start by sayin some of you might remember me and my car "the beast" pictured below. it was a long a fun project and ended with...

running stock cams and I am only pulling about 16 or 17 hg<p>Car idles rough with all new vac lines and gaskets.<p>

I have a 1992 B3 2.0 16V which has always run like a dream until about a week ago when it died completely. I pulled it home and dropped the external...

using a 1ml graduated cylinder and motor oil, calculated my 2.0 16v head combustion chamber at 47cc. This was with valves in a clean chamber not...