i have a 1990 vw jetta gl & it won't hold an idle. like it starts right up every time but if im not holding the accelerator, the idle will...

i had to pull the distributor because it had corroded put it back in wouldn't fire brought it to tdc pulled to plugs cleaned and re gaped them put...

I have an '82 8v Scirocco with a TT 268 cam and TT adjustable cam gear. I cut the exhaust off, put a header on, and am preparing to have a custom...

I'm looking for the clips that attach to the water/cooling pipe and hold the engine harness. They look identical to these... However, I bought a...

A great replacement for part numbers 043-905-115-C, 211-905-115-B , 211-905-115-C, 211-905-115-D We just got in a bunch on these coils and are...

Picked up another dead 92 cabby - the car has been sitting for some time and the timing belt was very worn /old. It appears that someone had been...

anyone have any pics of there set ups? this i the route in considering going down and want to have an idea of the outcome.

Just got the car, its been sitting for about 5 years.<br>when you try to start it it will fire on the first crank then die. Checked the spark and its...

Hey guys, I tried posting in MkII forums, CIS forum, no replies, so I'll try my luck here... I've about run my course with this one. I used the...

1984 rabbit gti engine but using a 1978 Cis (which is the year of the car). The cold start valve turns on when cranking but then it stays on. Anyone...

92 GTi Digi2 8v ABA. I have no vacuum leaks, grounds are clean, New spark hardware from the coil to the plugs and everything in-between. I will be...

Replacing my head gasket has turned into a full on rebuild. I've decided to keep both the original head and block. No ABA for this build... Partially...

I just bought an 86 Scirocco 8v and the car starts but then dies. I replaced the ignition switch because that's what a common issue is with them...

so do most people start with idle screw all the way in and backed out just enough to keep it idle.. and then adjust co screw... i have turned and...

started up my gti today and started to drive about a minute down the road i stopped at a stop light after that the car seems to have half the power....

My 1984 GTI with the "toilet bowl" down pipe is making a lot of ticking exhaust sounds from the manifold-to-downpipe area. I replaced the downpipe,...

Quick Question.. What sensor is this? http://i38.photobucket.com/albums/e150/xtremevdub/My%20Corrado/CORRADO%20ABF/CIMG1719_zpsd16e1a6c.jpg Is...

Was on my way to work, got stuck in some stop and go traffic, Car suddenly losses all power, gas pedal was really weak to respond, while trying to...

Hey everyone, Kinda stumped at the moment. I've been working on getting my '79 CIS 8V running decent after putting it all back together. It has a...

I have a JH that is getting a big valve hydro head and am wondering if it will be ok to run. Read that I may need a different oil pump also to...

I have been thinking about making a CNC valve cover for my 8v. Why? Because. :D I was wondering if you guys have seen one before? I know it is...

Mk2, '88 Jetta GL 8v, anyone have an accessory belt diagram? I can't get my drive belt off. Loosed the alt, loosed the a/c, still won't come off....

I have a 92 mk2 Gti that has the ABA block swapped in, and I think the knock sensor is bad. What are symptoms that a bad knock sensor would cause? I...

i wanna know what's the benefits of the adjustable cam gear my engine is 8v 2.0 2E what' the adustable can add to my engine and why i cant do what...

ok so, my "new" 89 Wolfsburg has run its temperature up to 3/4's on the gauge consistently and stays there without any other issues. I have just...

Ok , new here to the 1.8, please give me some kind of hope:( Just bought a 86 cabrio, the engine starts and idles fine, but as soon as you try to...

what is normal for temp gage reading. mine was blow half. and took long time for gage to move when cold. today installed new temp switch.now driving...

So, i just picked up a 89 carat jetta for my girls commuter car. the thing runs flawless. I was driving it, and the temp gauge was sitting right in...

I'd like to find a replacement for my injector harness if possible. However, I'd like a brand new part since the only thing wrong with mine is a few...

Is it possible to use the three CIS sending unit in a digi 2 car if I spice the wires and use the three prong female adapter?