im looking for info on a diy carb set up i want to go with a 2 barrel on my 1.8 looking for the best and not to spendy route with this

Alrighty, I've got carb'd 16v that's going in my mk1 rabbit I'm planning to either get a custom rad made to sit below my velocity stacks or use a...

Hello everyone!<p>This is going to be my first write up. Please feel free to ask questions and make suggestions! <IMG NAME="icon"...

I just inspected then replaced the Carter M 60238 mechanical fuel pump on my 1.7L Rabbit. The pump was purchased from Autozone in 2005 so it is 7...

Right now, I have a 9a 16v running Digifant 1 with an SNS chip. I'm currently building an ABA/16vT and might as well go megasquirt because....well,...

I have some Weber 32/36 carb with k&n filter and VW intake manifold. Jetted for some more power, thats what the add has told me when i purchased...

it's just a little question about my carb's conversion in progress. i'm not sur if i have to replace the oem fuel pump by my carter fuel pump + my...

SOLD I'm moving, so my current project is getting parted out. I have a brand new, unused 034 ECU with an untouched flying lead harness for...

hi, Is is possible to go with a programmable injection on a direct injection engine? thank you

And if you don't like 'em...try to keep the hate posts to a minimum, ok? <IMG NAME="icon" SRC="http://www.vwvortex.com/vwbb/wink.gif" BORDER="0">. ...

Not 100% sure what is out there in the world of side draft's. I am very new to the smaller multiple 2 barrlo carb setups. for my build i am...

Was searchin around to edumacate myself on MS2 and such, thought I may share this for any MS2 and MS noobs like myself Good read

is this a pretty straight forward no strings attached switch, or am i into disassembling the whole thing with special tools involved (such as press)

Good evening all, haven't posted in a while, but was hoping for a little advice for a problem I'm having at the moment. Paul(need_VR6) has been a...

Hey so i dont know a lot about carbs but I want to put some on my project car. Would the above mentioned carbs be a good fit? Engine ia 1.8L 16v ...

i just picked up a set of Dellorto 40's with out stacks, im wondering what length people are running in here? if you have pics for clearance purposes...

For you guys looking into different options for you engine management needs, I just installed an AEM EMS4 on my 2.0T NB (early MK4) . Same setup...

Need help wiring up my megasquirt v2.2 in 87 Jetta 16v. some good pics of it would help a lot the wiring diagram is kinda suck. I'm better with pic...

Posting for a friend.....<p>I have for sale two 45 DCOE Weber carbs. They are old (Bologna models) but in very good shape. They ran on my GTL...

Hi folks, I was wondering if someone had ever scoped the crank/cam raw signal together for a mk4 2.0l 8v (VR crank vs. Hall cam). I’m in the...

When you start considering your business's online presence, one of the first things you should consider is web design. Think of this website as your...

ABA with Dual type 4 downdraft SOLEX 32-34 PDSIT-3's. I'm all for odd carb setups.. My personal fave has been RV Block with ABA head and a Holley 450...

Hey, for those guys that have swapped cis over to carbs, I have a couple questions. First, what did you do with the cis control pressure regulator?...

I don't have a plug for the vacuum line on my short runner intake manifold rowland for my setup.( 16v weber 45dcoe.) my question is, have it a place...

Ok so here is the build I am doing, iv got an 83 1.7l 8v CIS Rabbit convertible, I also have an 88 rabbit GTI convertible 1.8L 8v CIS I got for...

i was wondering if the stock crankshaft sensor can be use with megasqurit? my bently manual shows the wiring to the sensor but the only wire i can...

So I get a nasty vapor lock issue when it above 70 degrees and have about 3 gallons of fuel left in the tank. When I remove the gas cap it sounds...

So i'm evaluating cost on my MS conversion, and I've schemed somethin up... Buy a MS1 3.0 preassembled and pop a MS2 Daughterboard in with the...

Is there a stand alone system that will play nice with the MKVI Golf cluster and ignition? AND if not, what's the workaround for the MKVI TB...

I got my MS ecu so its time to get started with my first megasquirt install. I'll have a lot of questions along the way and your feedback is welcome....