Alrighty, I've got carb'd 16v that's going in my mk1 rabbit I'm planning to either get a custom rad made to sit below my velocity stacks or use a...

I'm running off the 60-2 crank wheel on my aba. Whenever the rpms get to 4000 rpms the signal goes crazy, bouncing from 4000-6000rpms. I've put a 10k...

Hello everyone!<p>This is going to be my first write up. Please feel free to ask questions and make suggestions! <IMG NAME="icon"...

I ran megasquirt for what seems like forever, fuel only. I finally went with spark. I have a little difficulty with setting timing. Everything I have...

Hey guys. So I have my OBD2 Supercharged VR up and running on a V3 ms2. Ive been working on getting the VE tables all squared away and will likely...

So... I upgraded my 88 16v Scirocco from CIS-E to Motronic 5.9 from a 99 ABA Jetta. Pics Here:...

MS2-extra firing 1 EDIS4 coil. Somewhere along the way, trying to tune the 16V, coil A output died. I know it worked at one point because the plugs...

Need help wiring up my megasquirt v2.2 in 87 Jetta 16v. some good pics of it would help a lot the wiring diagram is kinda suck. I'm better with pic...

:D post only pictures of your set ups for everyone to enjoy :D

Not 100% sure what is out there in the world of side draft's. I am very new to the smaller multiple 2 barrlo carb setups. for my build i am...

Im looking to buy a set of dual Dellorto DHLA 45 Carbs, non-emission-type, in good condition. It would be great to get the Linkage, 8v...

Does the Lugtronic obd2 vr6 PnP harness come pre-wired and pre-programmed for A/C?

Just curious, and I feel like I've read it somewhere on here, but when converting to carbs with the use of a saab 900 vac advance distributor on a...

MS II, 3.57 , latest firmware. Wasted Spark, 3 coils. Using stock VR sensor. Started...some tuning, 3100 lost sync... Remembered...

Ok, before anyone freaks out, I know this is not a cut and dry topic and that there is no single "best" way to build an engine. I'm just looking for...

Aside from other tuning issues my car will not start in the cold weather. I read a few old threads where need a vr6 mentioned 300% at 32 degrees,...

I got my project running but it hasn't been perfect. RD 1.8L Block with well over 200k miles on it, g60 head and cam, atp manifold, t3 "super 60",...

Ok so im planning on doing a carb build on my ABF. It currently has a built head and decked head. Forged internals and arp everything. My plan is to...

I have MS1 with wasted spark set up installed on my 16v. I'm having a communication issue. When ignition is turned on, Tunerstudio will go live...

I just inspected then replaced the Carter M 60238 mechanical fuel pump on my 1.7L Rabbit. The pump was purchased from Autozone in 2005 so it is 7...

Hey so i dont know a lot about carbs but I want to put some on my project car. Would the above mentioned carbs be a good fit? Engine ia 1.8L 16v ...

is this a pretty straight forward no strings attached switch, or am i into disassembling the whole thing with special tools involved (such as press)

So I get a nasty vapor lock issue when it above 70 degrees and have about 3 gallons of fuel left in the tank. When I remove the gas cap it sounds...

im looking for info on a diy carb set up i want to go with a 2 barrel on my 1.8 looking for the best and not to spendy route with this

Right now, I have a 9a 16v running Digifant 1 with an SNS chip. I'm currently building an ABA/16vT and might as well go megasquirt because....well,...

I have some Weber 32/36 carb with k&n filter and VW intake manifold. Jetted for some more power, thats what the add has told me when i purchased...

it's just a little question about my carb's conversion in progress. i'm not sur if i have to replace the oem fuel pump by my carter fuel pump + my...

SOLD I'm moving, so my current project is getting parted out. I have a brand new, unused 034 ECU with an untouched flying lead harness for...

hi, Is is possible to go with a programmable injection on a direct injection engine? thank you

And if you don't like 'em...try to keep the hate posts to a minimum, ok? <IMG NAME="icon" SRC="http://www.vwvortex.com/vwbb/wink.gif" BORDER="0">. ...