Fresh 3.1L 12 valve VR6 short block for sale, 85mm JE pistons stock compression. New timing chains, tensioners, oem sealant used used to seal cover,...

Located in Indianapolis, I am looking for a local buy! PM me if you have one and want to sell it! No spun bearings or any problems.

For sale Matrix Integrated 3.1 VR6 12v short block. 85MM JE pistons, all new bearings and timing chains. Also have new correct 85mm head gasket to go...

the engine runs good with 187k i bought it thinking i was going to get the car back on the road but have decided to part it out. as of right now you...

This is a rebuilt AEB large port head all stock. I got it for a deal and was going to use it but ended up with another head I am going to use...

BIG VR6 12 VALVE TURBO PROJECT I NEVER FINISHED. MOST OF THESE PARTS ARE BRAND NEW OUT OF THE BOX.NO LOW BALLERS. I WILL WORK WITH YOU ON A PRICE AS...

Im selling an obdi 1 germany stamped aba head, upper and lower intake manifold, and exhaust manifold. It is an obdi germany stamped head. ...

Savani Auto Parts has quite a few Motor and transmission swaps available as well as spare parts for the motor swaps! 1.8T Engine Swap- $1,500 ...

Built for pressure ABA bottom end Block-> hot tanked cylinders honed painted black Rotating assembly-> OBD1...

FS: Solex/Mikuni 44PHH Sidedrafts and intake manifold, gasket kits, Pottstown PA, Price: $700 owner will not split up the parts. PM all...

I'm parting my car out. It has been my pride and joy for the past few years, however, I think it's time to move on in life. This whole setup just...

from a high compression 1.8 8V motor. not sure of exact engine code, but these are 10:1 pistons. $25 plus shipping...

cleaning out the garage. $10 plus shipping Tampa, FL...

Not sure of the history of this, purchased from a turbo buff many years ago. i never used it. Audi MC turbo pistons installed in a rabbit JH 1.8...

I need this motor gone I have no room for it anymore and am out of the vw scene so my loss your gain. I have all receipts for every part that totals...

Has 190k on it but in really good shape as far as I can tell. The engine ran and was pulled apart for a 3.0L project that never happened. $100+...

Selling a spare Aeb short block I picked up for a project but decided to abandon the project. The motor from what I was told had 200k on it, the head...

As stated Mk3 2.0l obd2 with 115k wih new parts Water pump Timing belt Crank sensor Wires Plugs Dizzy cap n rotor

BRAND NEW BLACK PAINTED SCHIMMEL PERFORMANCE FULLY BUILT VR6 12 VALVE 3.0 LITER SHORT BLOCK STAGE 2. SPTURBO JE CUSTOM PISTONS 8.5 TO 1 .100...

Obd2 Vr6 Swap has about 125k Trans as well Was told it was running and driving fine. Haven't had much time to mess with it as of yet,I know it...

Mk3 12v Mild port and polish All new parts less than 5000kms old Ferrea valvetrain (springs/retainers/locks) New giudes and seals $1000 plus...

ARP main studs for newer style 4 cylinder blocks, new in box, $105 shipped.

This is out of my 12 beetle. Entire stage 3+ from apr. intercooler, intake, ECM, hoses,turbo, apr built motor with pistons and rods. Has under 1000...

<B>All Items Include Free Ground Shipping in the lower 48 states</b><p><IMG SRC="http://www.fourseasontuning.com/parts/021107081SET.jpg"...

We are selling a perfectly good working engine that was removed from a 08 R32 w/ 47k miles. Everything shown in the picture is included in the sale....

I have had mk5 GLI's for 7 years and in that time one cam accumulate some parts. so for sale is some parts laying around ;) exhaust cam and chain...

I am selling my fully refinished 12v vr6 head. It will not come with camshafts or cam caps. It comes with the following: -3 Angle Valve Job...

Never got around to using these. 81mm 8.5:1cr forged JE piston set; for 1.8L 16V w/ 2.0L 16V(9A) head; w/ rings, wire locks, and fitted 22mm pins....

i have a 2.0 engine originally pulled from an automatic obdII jetta. i do not know the miles, but the engine runs good, and has good compression. i...

sold complete used engine.. not available anymore.