Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: ChrisAudi80

    Page 1 of 2 1 2

    Search: Search took 0.66 seconds.

    1. Replies
      0
      Views
      71

      FS: VEMS ECU with harness for 1.8T

      I bought this VEMS ECU with harness, boost controller, WBO2 sensor, injectors and new coils (06A) a few months ago. Some of you might have seen that ad.

      It originally came from bulldoser62 who...
    2. I am glad you did exhume this. I did find a...

      I am glad you did exhume this.

      I did find a way to get rid of the AFM. I put a piggyback ECU in my B4 Audi 80 with a 2.0E Digi-II with autotrans. This piggyback can be run in AFM elimination mode....
    3. SOLD!!

      SOLD!!
    4. YGPM!

      YGPM!
    5. Replies
      152
      Views
      104,090

      Yes. Read the OP again.

      Yes. Read the OP again.
    6. Nobody?

      Nobody?
    7. VW097 (01N) transmission; power/torque capacity?

      I have been searching a lot, trying to find out what the power and/or torque handling capacity is for the 097/01N auto trans. I know they were also used for the 2.8 V6, so should be able to handle...
    8. I know this is an old thread, but I thought maybe...

      I know this is an old thread, but I thought maybe one of these kits could be useful:
      http://www.splitsec.com/products/mafkits/MAFkits2.htm

      I read the early posts and noted the comments about CFM...
    9. Replies
      48
      Views
      5,067

      Just run distilled water and maybe water wetter....

      Just run distilled water and maybe water wetter. It would be good if you could have a bleed point on top of one of your AWIC end tank, which ever end tank is highest. The reservoir will bleed just by...
    10. Replies
      48
      Views
      5,067

      From what I have read so far of successful AWIC...

      From what I have read so far of successful AWIC setups, that sounds good. See if you can put a little bleed valve at the highest point of the system.
    11. Replies
      3
      Views
      1,610

      You know what I wanted to post, but after...

      You know what I wanted to post, but after re-reading the forum rules, could not.
      I was referring to my own post which I edited.

      Not referring to your OP.
    12. Replies
      48
      Views
      5,067

      You really need a bleed valve at the highest...

      You really need a bleed valve at the highest point of the system. That might be it.
      Others have used the Cobra pump with success.
      Any reservoir needs to be away from the heat of the engine bay.
    13. Replies
      48
      Views
      5,067

      Do you have any pics of the set up? Are you sure...

      Do you have any pics of the set up? Are you sure you have air bled it completely?
    14. Replies
      3
      Views
      1,610

      NM. Not allowed.

      NM. Not allowed.
    15. Replies
      108
      Views
      14,236

      Fantastic AWIC/IM design. Your throttle response...

      Fantastic AWIC/IM design. Your throttle response will be snappy.
    16. Replies
      2,885
      Views
      868,221

      Lykke til med salg :thumbup:

      Lykke til med salg :thumbup:
    17. Replies
      2,885
      Views
      868,221

      Read through this thread over the last 2 days....

      Read through this thread over the last 2 days.
      Words fail me on the awesomeness of this build.

      The SS welding is pure porn.
    18. Replies
      152
      Views
      104,090

      OK, thanks for the advice.

      OK, thanks for the advice.
    19. Replies
      152
      Views
      104,090

      No, I PMed you on MG. What I said was: "I...

      No, I PMed you on MG.
      What I said was:

      "I have been considering swapping in an AEB into my FWD B4 2.0E ABK automatic.
      The way I see it, I can go 2 ways.

      1. Buy an A4 B5 FWD half cut (manual...
    20. Replies
      152
      Views
      104,090

      Thanks for replying Issam. What about water and...

      Thanks for replying Issam. What about water and oil lines for the turbo. Need to tap those too?
      I am guessing if I do this, I will need some kind of SEM?

      btw, I sent you a fb message. Did you see...
    Results 1 to 20 of 21
    Page 1 of 2 1 2