Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: Prof315

    Page 1 of 13 1 2 3 4

    Search: Search took 0.66 seconds.

    1. Go standalone.

      Go standalone.
    2. Replies
      3
      Views
      208

      Go! It's a lot of fun and always very...

      Go! It's a lot of fun and always very informative. I am hoping to be able to go but it's right after I get back from vacation so not sure if it will be in the budget.
    3. Switch to MS2/Extra code. Here is a link to...

      Switch to MS2/Extra code. Here is a link to download it: http://www.msextra.com/doc/auth.php?f=ms2extra/files/release/ms2extra_3.3.2_release.zip Use the loader that is included with it
    4. Replies
      3
      Views
      299

      that would work

      that would work
    5. Replies
      3
      Views
      299

      1. Throttle body: You can use either the OBD1 or...

      1. Throttle body: You can use either the OBD1 or OBD2 throttle body. Either way if you want idle control you will need to build the PWM idle mod (TIP120/122mod) The OBD2 throttle body uses a...
    6. How is the fuel pump wired to MS? MS is designed...

      How is the fuel pump wired to MS? MS is designed to run the fuel pump by grounding a fuel pump relay it DOES NOT provide voltage.
    7. You are using the wrong setting. You want basic...

      You are using the wrong setting. You want basic trigger not toothed wheel and capture on the falling edge using the dizzy. But if it's an ABA 16V why aren't you using the factory crank position...
    8. Reflash firmware with the boot jumper installed.

      Reflash firmware with the boot jumper installed.
    9. Also you may want to try swapping your capture...

      Also you may want to try swapping your capture edge or sensor polarity. I have seen that cause this problem as well.
    10. You may also want to try turning OFF the noise...

      You may also want to try turning OFF the noise filtering. I had a VW 60-2 trigger set up that would break up around 4-5K and it WAS the noise filtering causing the problem.
    11. Well I have been running an MS3-Pro on an ABA...

      Well I have been running an MS3-Pro on an ABA since beta testing the 3-Pro started and I solved the sync loss at 2000 rpms issue with a 10K 1/4W resistor in series on VR+ it's been almost 20,000...
    12. Put a 10K ohm resistor in series on VR+. Jean's...

      Put a 10K ohm resistor in series on VR+. Jean's conditioner board uses the same basic hardware as a v3.57 mainboard, Microsquirt and MS3 Pro all of which need a 10K to prevent sync loss above 2-5000...
    13. Replies
      4
      Views
      568

      Nice numbers especially when you consider that...

      Nice numbers especially when you consider that Mustang dynos typically read 10% lower than a Dynojet or Superflo
    14. paper

      paper
    15. Replies
      8
      Views
      768

      Changing deadtimes will ways require some...

      Changing deadtimes will ways require some retuning. Ironically lowering deadtime requires that you ADD fuel.
    16. Replies
      10
      Views
      392

      If both your new chip and the stock chip work ok...

      If both your new chip and the stock chip work ok with stock injectors but not bigger ones it's safe to say that both are meant for stock injectors. Get the correct chip for the injectors you are...
    17. You have low oil pressure. Probably worn main or...

      You have low oil pressure. Probably worn main or rod bearings.
    18. Replies
      45
      Views
      1,893

      If it's throwing a P0304, run a compression test...

      If it's throwing a P0304, run a compression test on #4 Cylinder. You probably have a tweaked exhaust valve.
    19. Replies
      18
      Views
      947

      Did you also set idle valve operation to inverted...

      Did you also set idle valve operation to inverted in the Idle control settings? You need to so that more DC = higher idle. What you are doing by running the idle motor this way is going from the...
    20. Replies
      18
      Views
      947

      Well I see a couple of things going on right off...

      Well I see a couple of things going on right off the bat that are going to be an issue.

      #1 What firmware version are you running? Looking at the screen shots it's old. Do yourself a huge favor...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4