Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: Chickenman35

    Page 1 of 13 1 2 3 4

    Search: Search took 0.74 seconds.

    1. Replies
      69
      Views
      24,476

      :thumbup:

      :thumbup:
    2. Post some pictures of your system when you're...

      Post some pictures of your system when you're done. I might also get rid of my H/Lamp washer tank and put a catch can in there and would like to see how you did it. But I like the 20 gallon ( joke )...
    3. Good luck with your project. Just make sure that...

      Good luck with your project. Just make sure that when you select a catch-can you get a non-vented style. A vent to Atmo with one of those K&N style breather filters on top renders the whole PCV...
    4. The more I think about this the more I like the...

      The more I think about this the more I like the solution of the single catch can between #2 and #5.

      034 Motorsport also makes a Billet adapter with a nipple. That would be much easier to plumb...
    5. You could...if there was any room. Next to...

      You could...if there was any room. Next to impossible to do it with the stock plastic parts, but if you modded things with -10 AN things and did a reroute between #2 and #5 it's possible. That would...
    6. For 165,000 miles they look pretty good to me. No...

      For 165,000 miles they look pretty good to me. No major worries IMHO. Micro polish the crank, check dimensions and you should be good to go.

      A little bit more of bearing " scratching " from...
    7. You have fuel. You have spark. But you have NOT...

      You have fuel. You have spark. But you have NOT determined that you have compression. That was mentioned in the very first reply. Don't keep guessing. Slap a compression gauge on that thing and...
    8. Replies
      973
      Views
      103,840

      ^ Ah... that's makes sense. Supply and demand. ...

      ^ Ah... that's makes sense. Supply and demand.

      That's why I like a caliper such as 4 or 6 Piston WilWood Superlites. Pad choice is always plentiful and Circle Track suppliers always have...
    9. Replies
      973
      Views
      103,840

      $350 for a set of Boxster front Pagid RS4-4's...

      $350 for a set of Boxster front Pagid RS4-4's seems a bit high. Without too much searching I found them under $250 from several USA suppliers.

      PFC and Carbotech would be a good choice as well.
      ...
    10. I can't remember Max. You running SP or Street...

      I can't remember Max. You running SP or Street Mod? Was just browsing the 2015 SCCA Solo Rules last night, and apparently SP rules require that the vehicle has an operating hand brake ( or foot...
    11. Interesting... I've haven't had to use that...

      Interesting... I've haven't had to use that technique in years, all of our sites are dead flat. Our Hillclimbs of course have a start line wheel block, so no handbrake needed. But I do notice the...
    12. Handbrake and all associated cables etc can go....

      Handbrake and all associated cables etc can go. Unless you plan on doing Rallycross as well!!

      What are you running for rear Calipers these days?
    13. Replies
      44
      Views
      1,824

      Whatever makes the engine happy :thumbup:

      Whatever makes the engine happy :thumbup:
    14. Replies
      44
      Views
      1,824

      I would recommend plumbing back into the Intake...

      I would recommend plumbing back into the Intake manifold. The exhaust scavengers tend to over scavenge.

      Copy the AEB system. Much simpler and more reliable than later systems. AEB system does not...
    15. Replies
      44
      Views
      1,824

      That makes sense. High levels of detergents can...

      That makes sense. High levels of detergents can be detrimental to ZDDP life span. Might explain the lack of Calcium reading.
    16. Replies
      44
      Views
      1,824

      If this is a DD, you may want to re-consider your...

      If this is a DD, you may want to re-consider your venting system. Quite a few guys here are switching back to complete sealed PCV systems after doing oil analysis and seeing how much acid and carbon...
    17. Replies
      44
      Views
      1,824

      Also, can you take some more pictures with closer...

      Also, can you take some more pictures with closer detail of the upper bearing shells. I t looks like there may be some " Fatigue " markings, but I can't quite tell because the pictures are too far...
    18. Replies
      44
      Views
      1,824

      " Fully Vented " PCV system? Can you take a...

      " Fully Vented " PCV system? Can you take a picture of your setup or be a bit more specific? PCV systems must be a closed system.

      They cannot have VTA points such as Catch cans with K&N style...
    19. Replies
      44
      Views
      1,824

      Thats' looking like possible acid etching on the...

      Thats' looking like possible acid etching on the bearing surface and back side. See the Clevite bearing failure guide.

      Small scratches on crank journals could be from oil contamination from an...
    20. Replies
      6
      Views
      634

      If I'm reading this right..you're trying to run...

      If I'm reading this right..you're trying to run 630cc Injectors on a Stock ECU Tune?? Is that correct?? If so it's a wonder it even runs...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4