Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: OEMplush1

    Page 1 of 3 1 2 3

    Search: Search took 0.56 seconds.

    1. Replies
      5
      Views
      379

      Thanks for your help guys. I ordered one from...

      Thanks for your help guys. I ordered one from ECS and I was able to get out after soaking in Kroil then using some vise grips.
    2. Replies
      5
      Views
      379

      HFFP pressure nut and valve

      Hi guys looking for a little help. I was swapping out my cam follower and somehow my 6 point 13MM deep well socket rounded off the nut on the relieve valve. I tried many different approaches to...
    3. Replies
      7
      Views
      243

      Try raising up the car!

      Try raising up the car!
    4. Replies
      2
      Views
      196

      Replace your turbo, seal is on its way out. APR...

      Replace your turbo, seal is on its way out. APR KO4 is the best bang for the buck.
    5. Replies
      7
      Views
      296

      Try search, I have saw this title for a thread...

      Try search, I have saw this title for a thread only around 1000 times over the last 6 years.

      Don't waste your time unless you have a high flow fuel pump, you will just be plagued by fuel cuts. ...
    6. Replies
      3
      Views
      321

      So is anyone running anything wider than a 225? ...

      So is anyone running anything wider than a 225? ET is 45, btw.

      What is everyone on here into stretch and 205's that handle like garbage?
    7. Replies
      3
      Views
      321

      Tire and Wheel fitment, not a newb.

      Hi guys just looking for a little input. I have run many sets of wheels and tires on GTI's MK II-VI.

      The car now sits on Koni Coils that are almost to the top the threaded bodies. I have been...
    8. I have no plans to sell. I do have 964 plans...

      I have no plans to sell. I do have 964 plans though with an RS build.
    9. Thanks for the replies APR!

      Thanks for the replies APR!
    10. Are you going to offer any sales on Brembo 6...

      Are you going to offer any sales on Brembo 6 pots? Why is APR no longer a VW racing dealer?
    11. Sounds like it could be your rear wheel bearings....

      Sounds like it could be your rear wheel bearings. They are a common part to fail in the rear of your car. Mine didn't even last as long as the fronts. I changed and the loose feeling in the rear...
    12. You get what you pay for... Buy some Koni coils...

      You get what you pay for... Buy some Koni coils and have no trade offs in ride quality. It will also have damping that will make driving faster easier.

      If you want a race car buy some linear...
    13. Replies
      1
      Views
      272

      Limited Slip Install for DSG

      Does anyone know of a shop in NY or bordering that is experienced with DSG transmissions and installing LSD's? I would prefer to remove the transmission in my garage and just put on a pallet and...
    14. Replies
      4
      Views
      793

      I did the oil at the same time I pulled the...

      I did the oil at the same time I pulled the covers and again last week. This is the fourth follower in the car since new, I have 72K and the last 20 were KO4 and hard miles.

      Car is running fine,...
    15. Replies
      5
      Views
      315

      Someone must have FK's and some advise. I have...

      Someone must have FK's and some advise. I have owned 4 sets of coil-overs and never run into a sway bar rubbing issue.
    16. Thread: Tsi vs fsi

      by OEMplush1
      Replies
      34
      Views
      5,303

      I have mkv FSI GTI, mkvi TSI GTI and both are...

      I have mkv FSI GTI, mkvi TSI GTI and both are stage 2, the fsi pulls a few cars when run from 40-110.

      FSI is good but changing follower and hffp is a pain in the ass.
    17. Replies
      4
      Views
      793

      cam follower hole

      Went to swap in a new follower and realized I had a hole thought my old follower. I pulled the valve and cover to the right and couldn't find any pieces of metal. I also had no damage to the lobe,...
    18. Replies
      5
      Views
      315

      FK's rubbing somewhere

      Put in FK's and car is low. Took out helper springs but I am getting some rubbing somewhere. It was my sway bar but I have raised it up but still some rubbing could it just be the springs?
      ...
    19. Replies
      29
      Views
      5,082

      This car has been on of my fav's since looking it...

      This car has been on of my fav's since looking it over last year. In person this car is faultless, owner went to great lengths to keep clean. GLWS!
    20. Replies
      48
      Views
      6,942

      I own a KO4 Eurojet kit with fmic, its not that...

      I own a KO4 Eurojet kit with fmic, its not that large and the welds are not that nice. If you compare it to APR or the CTS unit you will see how much higher quality the parts and construction is not...
    Results 1 to 20 of 57
    Page 1 of 3 1 2 3