Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: Anony00GT

    Page 1 of 13 1 2 3 4

    Search: Search took 0.45 seconds.

    1. That part number is correct for the OE Beru spark...

      That part number is correct for the OE Beru spark plugs.

      Alternatively, you can use NGK's: PZFR5J-11 Laser Platinums.
    2. Thread: CEL flashing

      by Anony00GT
      Replies
      1
      Views
      117

      Dude, put the bottle down and type slower. Then...

      Dude, put the bottle down and type slower. Then proofread your stuff. Wow.

      Exactly what fault code(s) are you getting? Were the replacement O2 sensors genuine direct fit Bosch or OE? When's...
    3. Replies
      1
      Views
      110

      Definitely a tuning issue. I've never heard of...

      Definitely a tuning issue.

      I've never heard of Berg, maybe try another tuner?
    4. Replies
      2
      Views
      353

      You got lucky. Federal warranty is 8 years/80k...

      You got lucky. Federal warranty is 8 years/80k miles on emissions, you're out of that.

      Just as an FYI, BBW engines must be fixed correctly. There are no cheap replacement parts or work-arounds. ...
    5. Replies
      2
      Views
      145

      06A 133 064H is the one you want, without cruise...

      06A 133 064H is the one you want, without cruise control.

      06A 133 066E is the one to use with cruise control.

      They are not interchangeable. Use the proper replacement part number for your car,...
    6. Make sure the replacement temp sensor is genuine...

      Make sure the replacement temp sensor is genuine OE from the dealer, not aftermarket. And replace the thermostat (again, OE, not aftermarket).
    7. Replies
      38
      Views
      1,118

      I'd just replace the valves and put the head back...

      I'd just replace the valves and put the head back on.
    8. Replies
      4
      Views
      321

      You cannot run a turbo setup on the stock...

      You cannot run a turbo setup on the stock injectors. You cannot run a turbo setup without a proper tune. Period.

      I'm running 12psi on a stock ABA bottom end, with 30lb injectors and a C2 stage 1...
    9. Sounds like you need to stop using junk starters...

      Sounds like you need to stop using junk starters and pony up the cash for a good one.
    10. Replies
      19
      Views
      1,024

      So much sarcasm, such an OP that doesn't make...

      So much sarcasm, such an OP that doesn't make sense.. :laugh:

      Seriously, to the OP. Do you mean your RPM's fluctuate between 600 and 800 at idle (or cold start), then it idles normally after...
    11. If you have VCDS, post up the full scan. Also,...

      If you have VCDS, post up the full scan.

      Also, if you have VCDS, you should be using that to perform the throttle ADP. The "key-on", "battery disconnect", "chicken dance", etc methods DO NOT...
    12. Thread: MAF issues

      by Anony00GT
      Replies
      6
      Views
      417

      Do not use a timing light to set the distributor...

      Do not use a timing light to set the distributor on this engine. Bring #1 to TDC with the mark on the flywheel, and the O|T mark on the cam gear and rear cover should also line up. Then line the...
    13. Replies
      1
      Views
      167

      That harness will only work with an OBDII setup....

      That harness will only work with an OBDII setup.

      The answers to your questions of "what wire does what/this wire goes where, etc" can all be found in the wiring diagrams, which are in the Bentley...
    14. What are your compression numbers? To do a...

      What are your compression numbers?

      To do a leakdown test, bring the engine to TDC on that cylinder (valves closed), and apply regulated air pressure through the spark plug hole. See where the air...
    15. Thread: MAF?

      by Anony00GT
      Replies
      3
      Views
      184

      Correct. CBPA uses a MAP sensor to determine...

      Correct. CBPA uses a MAP sensor to determine load and upstream wideband air/fuel sensor to adjust the mixture. There is no MAF.

      I haven't had to delve into diagnostics on one of these yet,...
    16. Replies
      38
      Views
      1,118

      You don't have to remove the big crankshaft bolt...

      You don't have to remove the big crankshaft bolt to replace the timing belt.

      Again, get the service manual and READ IT before you proceed any further.
    17. Yes. www.ross-tech.com

      Yes.

      www.ross-tech.com
    18. Replies
      2
      Views
      213

      I can't imagine why they wouldn't be...

      I can't imagine why they wouldn't be interchangeable. Try it and see if it works.
    19. Scan the car with a proper tool, preferably VCDS,...

      Scan the car with a proper tool, preferably VCDS, not the AutoZone generic OBDII. Post the scan here. That's the first step to diagnosing the problem(s) you're having.
    20. Replies
      5
      Views
      268

      The studs shouldn't spin. Turn the nut with an...

      The studs shouldn't spin.

      Turn the nut with an open end wrench and see if the stud is spinning.
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4