Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: MRosier

    Page 1 of 13 1 2 3 4

    Search: Search took 0.73 seconds.

    1. Replies
      11
      Views
      410

      The stuff we use is the HT. Good for up to 600*....

      The stuff we use is the HT. Good for up to 600*. I've never used the 4 before.
    2. PM sent!

      PM sent!
    3. Replies
      11
      Views
      410

      Yeah I swear by the Honda Bond. Stuff makes an...

      Yeah I swear by the Honda Bond. Stuff makes an epic seal if you wait for it to cure properly. I've used it on my oil pan and timing chain covers. And I used it almost everyday for one thing or...
    4. Replies
      22
      Views
      496

      The under-car piping is only 2" and is stainless...

      The under-car piping is only 2" and is stainless steel and will take some abuse. It doesn't hang any lower than the oil pan, big whoop.
    5. Replies
      22
      Views
      496

      These aren't my pics, but check out this link:...

      These aren't my pics, but check out this link: http://warped.org/photos/Cars/vrt/page/2 It's some dude's build thread on a GTI with some really good pictures.:thumbup:
    6. Replies
      22
      Views
      496

      OK, lots of things need to be cleared up here....

      OK, lots of things need to be cleared up here. First, the kinetics front mount for VR6 has always had the inlet turning downwards like that. The hot side piping runs through the tunnel under the oil...
    7. Replies
      11
      Views
      410

      I've let them cure 24 hours before. At the...

      I've let them cure 24 hours before. At the minimum, overnight. I work at Honda so 'Honda Bond' is readily available and I think the cure time on that is only 15-16 hours. If you get Permatex "The...
    8. BUMP! Found a core, just looking for piping! :)

      BUMP! Found a core, just looking for piping! :)
    9. Replies
      11
      Views
      410

      I've never gotten a good seal just by using a...

      I've never gotten a good seal just by using a fresh gasket. You can get a good leak free seal using sealant only if you let it cure properly but a problem that arises is the bottom of the pan is now...
    10. Were you able to retain the A/c condenser with...

      Were you able to retain the A/c condenser with this FMIC? Or is it removed? Great looking car! GLWS
    11. Replies
      3
      Views
      131

      one of the longer ones goes through from the...

      one of the longer ones goes through from the passenger side and threads into the bell housing on the back side by the right axle flange. two short ones are for the two upper holes just below the...
    12. Thread: MkIII + Meth

      by MRosier
      Replies
      24
      Views
      1,202

      HAHAHAHA best **** I've seen in awhile!

      HAHAHAHA best **** I've seen in awhile!
    13. lots of penetrating oil and trying to rotate the...

      lots of penetrating oil and trying to rotate the sleeve to get it free before pulling it out with needle nose vise grips should do the trick :popcorn:
    14. Replies
      3
      Views
      129

      PM sent

      PM sent
    15. Replies
      3
      Views
      129

      WTB: OBD2 VR6 Engine Wiring Harness

      Looking for just the engine harness for an OBD2 VR6 from the big round plug to the engine accessories. Unmolested please, thanks!
    16. Yes needle nose pliers should be able to get them...

      Yes needle nose pliers should be able to get them out. :beer:
    17. Replies
      2
      Views
      513

      Not trying to be "that guy". But I'm still...

      Not trying to be "that guy". But I'm still wondering why you want one of these. They were literally gutted factory manifolds with their "EIP Tuning High flow Manifold" stamped on the top.
    18. Replies
      22
      Views
      949

      Sounds like you might have a gauge cluster out of...

      Sounds like you might have a gauge cluster out of a 4cyl. car in there as far as the 5000rpms in 5th goes. Does your speedo go to 140mph or 160mph?
    19. Replies
      3
      Views
      445

      Do you have any better pictures of the EIP front...

      Do you have any better pictures of the EIP front mount and piping possibly off the car? Is the piping meant for a short runner or stock intake manifold?
    20. Sounds like you have an EIP tuning bottom/side...

      Sounds like you have an EIP tuning bottom/side mount intercooler?
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4