Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: Eric D

    Page 1 of 13 1 2 3 4

    Search: Search took 0.22 seconds.

    1. Thread: To old to dub?

      by Eric D
      Replies
      14
      Views
      428

      http://www.youtube.com/watch?v=VPVMsYjVfEE ...

      http://www.youtube.com/watch?v=VPVMsYjVfEE


      Never too old!
    2. Replies
      14
      Views
      430

      I copied this from a reply I did years ago. I...

      I copied this from a reply I did years ago.

      I want to point out that there was a service bulletin years ago for 93 Corrados and Passats.
      It stated the ABS warnings lights may be on due to a...
    3. Replies
      2
      Views
      231

      Budget, Free parts, Free Labor, Extra Parts $$$,...

      Budget, Free parts, Free Labor, Extra Parts $$$, Daily Driver, Dependable, Better mileage.

      I don't see this ending well.

      How much does your friend owe you, and how much can you spend on the...
    4. Would be easiest to make the a-pillars extend at...

      Would be easiest to make the a-pillars extend at the base and cover in matching fabric.
    5. Replies
      14
      Views
      430

      If you read your Bentley service manual, you'll...

      If you read your Bentley service manual, you'll see they show the wear sensor wire in the brake chapter.

      Your second answer is partially correct, the pressure switch on the ABS module will also...
    6. Replies
      3
      Views
      277

      Terminal 30 is clearly marked. Anyone who owns...

      Terminal 30 is clearly marked.

      Anyone who owns a Bentley service manual and has read it, will know what that leads to.
      So bust out your manual and post your results.

      :popcorn:
    7. Swap parts: B3, B4 VR6 Passat and Corrado VR6...

      Swap parts:

      B3, B4 VR6 Passat and Corrado VR6 front cross member.
      Or stock Mk2, G60 Corrado front cross member with Vibra Technics front motor mount.

      K-frame (subframe) can be Mk2/G60 or Mk3...
    8. Title made me think of this pic I found on the...

      Title made me think of this pic I found on the net years ago.


      http://data.motor-talk.de/data/galleries/0/138/2070/16909000/dsc01049-35345.JPG
    9. Replies
      11
      Views
      509

      Many people don't realize that VW did sell a...

      Many people don't realize that VW did sell a Jetta GTI, it was a UK edition available in 8v and 16v.

      Have a look at the brochure....
    10. Replies
      23
      Views
      1,314

      Sad to know this base in Bamberg and the one in...

      Sad to know this base in Bamberg and the one in Schweinfurt are closing.
    11. Keep the dual mass if you don't want to hear...

      Keep the dual mass if you don't want to hear noise (till the DMF physically fails), keep the hp levels low, keep up on synthetic gear oil.
      Don't speed shift, keep an eye on the cable ends.
      The...
    12. Replies
      19
      Views
      1,569

      There are a few contributing factors that create...

      There are a few contributing factors that create this problem.
      1st, fuel cools the pump and a 1/4 tank is obviously lower than the fuel pump armature.
      This is a common failure dating back to the...
    13. Thread: Lifter Noise?

      by Eric D
      Replies
      2
      Views
      389

      A new lifter has a very short length of travel, I...

      A new lifter has a very short length of travel, I kid you know when I say its about 3 mm.
      Now compare that to a carbon fouled one which may only move 1.5 mm or not at all.
      I've posted in the past...
    14. Your noise is typical of a single mass flywheel...

      Your noise is typical of a single mass flywheel conversion.
      I warn everyone interested in a single mass flywheel clutch kit about the noise.

      If you used a dual mass flywheel, the noise wouldn't...
    15. You can verify if you have worn thrust bearings...

      You can verify if you have worn thrust bearings easily without dropping the pan.
      Pull on your crank pulley and push it towards the trans.

      Worn thrust bearings would leave metal flakes in your...
    16. Replies
      10
      Views
      399

      For me absolutely, most of Mk2s were purchased...

      For me absolutely, most of Mk2s were purchased for under $500, none were ratty all adult owned and complete.
      I seem to buy other peoples cars that they have given up on.

      There is a breather...
    17. Replies
      10
      Views
      399

      Only money if a part is bad and needs...

      Only money if a part is bad and needs replacement. Most items are cheap and shared with other models. The AFM is unique to the specific Digifant model, and Digifant 1 has a discontinued/ obsolete...
    18. Replies
      10
      Views
      399

      Digifant issues, better get a Bentley manual and...

      Digifant issues, better get a Bentley manual and read it cover to cover.
    19. Replies
      6
      Views
      199

      You have stock Mk2 100mm axles. Without seeing...

      You have stock Mk2 100mm axles.

      Without seeing the knuckle, I assume they used Eurospec 5x100 conversion brake kit

      http://www.eurospecsport.com/products/brakes/images/EBK-698-288-A2-5.jpg
    20. Replies
      9
      Views
      271

      Is this a Cali 16v? TPS, EGR temp prob and 02...

      Is this a Cali 16v? TPS, EGR temp prob and 02 sensor are in the back.
      The harness along the firewall would have lighting, coil power stage, purge valve, dpr and CIS air flow sensor plate position.
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4