Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: low_passat

    Page 1 of 13 1 2 3 4

    Search: Search took 0.88 seconds.

    1. Replies
      15
      Views
      293

      very close to flat, but definitely low 6's

      very close to flat, but definitely low 6's
    2. Replies
      15
      Views
      293

      Stage 2 will get you down to 6 sec 0-60 time

      Stage 2 will get you down to 6 sec 0-60 time
    3. Re-read the first sentence in the op's post. ...

      Re-read the first sentence in the op's post. He's looking for info on a 2010 CC
    4. The majority of the people in the area use the...

      The majority of the people in the area use the facebook group now.

      https://www.facebook.com/groups/ArizonaVW/

      There's a sunday night meet at Xtreme Bean in Tempe & wednesday night on the...
    5. Replies
      13
      Views
      3,486

      Yes, it's one piece. The 5 screw just hold the...

      Yes, it's one piece. The 5 screw just hold the cover on. There are 3 other screws that secure it to the cam chain cover.

      As for sealant, I really don't know. When mine was leaking I just...
    6. Replies
      13
      Views
      3,486

      The oring you purchased goes on the other side of...

      The oring you purchased goes on the other side of the vacuum pump where it goes into the cam chain cover. The seal to the outer plate is not available to purchase. It's not a round oring, it's a...
    7. Replies
      4
      Views
      291

      The port itself is sealed on the US TSI. The...

      The port itself is sealed on the US TSI. The manifold is likely used on other platforms, or markets where it is opened up and something is connected.

      Cost savings on mold tooling to have just...
    8. Replies
      11
      Views
      743

      Yes, you can separate the two grille pieces. ...

      Yes, you can separate the two grille pieces. It's a little tricky, but not too difficult. Just use a small flat screwdriver to pry the tabs apart. You'll may break a tab or two, but just take it...
    9. Interesting, did not know the 3.6 trans has the 3...

      Interesting, did not know the 3.6 trans has the 3 bolt mount like the manual & DSG. I thought all the tipronic trannys had the same 2 bolt & center vee mount.
    10. Replies
      2
      Views
      263

      There's this one ...

      There's this one

      https://www.facebook.com/events/1508267499432883/?ref_dashboard_filter=upcoming
    11. Sticky: Josh of PCCP It's a Passat wagon, also...

      Josh of PCCP



      It's a Passat wagon, also driven by Josh (a different one)
    12. you can buy one at any Autozone or O'Reily's for...

      you can buy one at any Autozone or O'Reily's for like $4
    13. The bracket you removed is the mounting bracket...

      The bracket you removed is the mounting bracket between the transmission & the mount that is bolted to the frame rail.

      The new bracket that you have is for an automatic transmission. The bracket...
    14. Found this in a Mk5 thread, but should be the...

      Found this in a Mk5 thread, but should be the same i think. This is for turning them off, so just reverse the setting
    15. Thread: ECU Swap

      by low_passat
      Replies
      9
      Views
      687

      IIRC it has to be the exact same p/n as yours,...

      IIRC it has to be the exact same p/n as yours, and then you would have to tow it to the dealer to adapt the immobilizer. Not 100% sure, but I think they just reflash the ECU which would erase the...
    16. Replies
      8
      Views
      760

      ^^^that o-ring goes on the diameter that fits...

      ^^^that o-ring goes on the diameter that fits into the cylinder head, as seen in this picture
      http://c1552172.r72.cf0.rackcdn.com/278140_x600.jpg

      The gasket the OP is ashing about is not...
    17. Replies
      6
      Views
      405

      You're going to need to monitor the wear on the...

      You're going to need to monitor the wear on the cam follower. Any scratches on the cam will accelerate follower wear.

      If you paid $700 for a hpfp & cam follower, you were overcharged.
    18. Fernando's Metal Polishing 702 W Melinda Ln #6...

      Fernando's Metal Polishing
      702 W Melinda Ln #6 Phoenix, AZ 85027
      (623) 581-2897
    19. Replies
      485
      Views
      43,152

      http://vimeo.com/23010188

      http://vimeo.com/23010188
    20. Yes & yes

      Yes & yes
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4