Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: sdezego

    Page 1 of 13 1 2 3 4

    Search: Search took 0.82 seconds.

    1. Replies
      269
      Views
      47,911

      Correct. That should be the one

      Correct. That should be the one
    2. Replies
      20
      Views
      731

      There are a few of these threads in the past, but...

      There are a few of these threads in the past, but this one is recent and interesting because the Country of Manufacture appears correct (even though it is a fake).
      ...
    3. Replies
      269
      Views
      47,911

      If I recall, it is the Spade Connector that is...

      If I recall, it is the Spade Connector that is oriented differently from the others (when you remove the Coolant Relay).
    4. Replies
      19
      Views
      611

      The only one I know of that makes -an type lines...

      The only one I know of that makes -an type lines for A/C is Aeroquip and they are $$$$. Look at NAPA if you have one or others I mentioned above. That can swage that front cross line out of a piece...
    5. Replies
      19
      Views
      611

      I have done all kinds of A/C swaps, mix matching...

      I have done all kinds of A/C swaps, mix matching etc. Currently running a VR compressor in my G60 that I made up adapter ends on the lathe and Used Passat B3 lines. That being said, a lot of NAPA...
    6. Replies
      14
      Views
      528

      Let me Clarify: When I say outer CV splines...

      Let me Clarify:

      When I say outer CV splines are the same for Corrado VR, Mk3 VR and Mk4 (I am referring to the CV spline to hub). I am not sure about the CV Spline to axle. I know the Axle...
    7. Replies
      269
      Views
      47,911

      Sounds like there is a cold solder joint (broken)...

      Sounds like there is a cold solder joint (broken) and temp causes expansion that causes the joint to lose contact. ..or possibly the Voltage regulator in the cluster. Easiest would be to look for a...
    8. Replies
      20
      Views
      731

      I would verify this is a REAL 044. I have never...

      I would verify this is a REAL 044. I have never had a problem with 044's
      What micron Filter are you running before your 044? You really should not be running a prefilter (other than the one on...
    9. Replies
      14
      Views
      528

      I think there must have been a misunderstanding. ...

      I think there must have been a misunderstanding. The outer splines are the same (yes), but the spline on the axle is different. I have the # of splines and measurements somewhere to compare and...
    10. Replies
      14
      Views
      528

      Something does not sound right. Mk2 Balljoints...

      Something does not sound right. Mk2 Balljoints are vertical where as the Corrado Vr and Mk3 VR Knuckles with the ("Plus" wider track/suspension) have ball joints on the angle as you describe. I...
    11. Replies
      269
      Views
      47,911

      T2h/1 and T2h/2 is the black 2x connector from...

      T2h/1 and T2h/2 is the black 2x connector from the Harness. In the later cars, that would plug into a later body or some other harness that would go to A1/2 and A1/4. These are actual spots in the...
    12. Thread: Headliner DUN

      by sdezego
      Replies
      28
      Views
      2,162

      You apparently live in a climate where there is...

      You apparently live in a climate where there is little humidity. In FL, 90% of the days here are 90% + humidity.

      My wife's '09 CC just dropped compeltely (finally). She always drives with...
    13. Replies
      5
      Views
      339

      I use some generic replacements that I got from...

      I use some generic replacements that I got from some big online warehouse (forget as it was about 6 years ago). It was either partstrain.com or autopartswarehouse.com (I think partstrain). Was not...
    14. Replies
      269
      Views
      47,911

      First, if you are swapping to the Digital...

      First, if you are swapping to the Digital cluster, I recommend getting the later T28 plug/pigtail to make your life easier. You can even use one from a Mk3. The Later cluster pigtail will have the...
    15. Checked in Bentley and Low pressure switch is .3...

      Checked in Bentley and Low pressure switch is .3 bar (not .8 bar), so yes, you would need to ignore the second terminal as 42DD suggests. Also, just noticed it is talked about here -> ...
    16. Replies
      45
      Views
      11,572

      Maybe I am re-stating the obvious, but you can't...

      Maybe I am re-stating the obvious, but you can't upgrade your master cyl if you still have ABS (based on your picture). The u/g is for people who converted to non-ABS.

      Now, that MC "may" be from...
    17. Either should work. Both are VDO senders for...

      Either should work. Both are VDO senders for 10bar/150psi. The 42DD is inexpensive. It has a second post for low pressure switch.

      In theory you could eliminate the banjo and separate low...
    18. I was thinking the same damn thing! The...

      I was thinking the same damn thing!

      The reason I started the "No Good Head units thread" had a somewhat Different impetus at the time, mainly looks, but I also wanted CD which I could care less...
    19. Replies
      5
      Views
      451

      Really hard to tell from the Video, but sounds...

      Really hard to tell from the Video, but sounds like a Bearing.

      Pull off serp belt and start to see if noise is still there. If so, pull off v belt too just to check.

      My guess it Alt or...
    20. VR6 cluster wiring harnesses should interchange...

      VR6 cluster wiring harnesses should interchange (at least they do here). IN fact you can use a Mk3 in Corrado Vr6 too.

      The only difference being that if you use the Later Corrado Vr6 or Mk3...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4