Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: rodperformance

    Page 1 of 5 1 2 3 4

    Search: Search took 0.67 seconds.

    1. Replies
      2,349
      Views
      343,580

      http://i1133.photobucket.com/albums/m590/rodperfor...

      http://i1133.photobucket.com/albums/m590/rodperformance/Mobile%20Uploads/WP_20150323_19_29_14_Pro.jpg
    2. Shot a Text if you havnt sold the kit!!...

      Shot a Text if you havnt sold the kit!! 939-644-0676 Roderick. Money on Hand!! Thanks in advance
    3. Replies
      2,349
      Views
      343,580

      head gasket stack

      In my case two set of pistons due to lean condition and even reused the head gaskets(not recomended)still no leakage!! Cooper spray and boost on!!
    4. Replies
      2,349
      Views
      343,580

      Mr West!!

      You can fit a techtonics distibutor adapter so you can use the digifant unit and since it has four Windows youre set to go!! Tsel/opto in mod on the board and good to go.i would recomend kp...
    5. Replies
      2,349
      Views
      343,580

      great vid

      Thanks Das one video speaks a million words!!
    6. Replies
      2,349
      Views
      343,580

      Das

      Dascoupe are you on 3.38? Also or just the gears?
    7. Replies
      2,349
      Views
      343,580

      ccm or ata

      Thanks pwb8! I wanted to keep my 3.68fd but to make it easier so i dont have to remove the gears out and fit them to the ccm shaft,plus lots of work and very little time to wrench on the car make it...
    8. Replies
      2,349
      Views
      343,580

      thanks

      3.38 final drive? Because im thinking to swap every thing from ccm to corrado 02a
    9. Replies
      2,349
      Views
      343,580

      final drive

      Hi folks!! Im wondering what final drive should i put on my turbo setup! Currently running 02A 3.68 but i have a ccm tranny out of a vr6 jetta.which would be better 3.38 or stick with 3.68?any...
    10. Replies
      2,349
      Views
      343,580

      gap

      I know you know but some times one forgets! 22-24 sparkplug gap!! I run bkr7-eix
    11. Replies
      2,349
      Views
      343,580

      paging brother Das!

      Das have you've been able to dyno again with the new engine?.I havent been able due to a spark misfire problem,so new sparkplugs msd coil and wires!! Will see but for now is clausured proyect till...
    12. Replies
      2,349
      Views
      343,580

      inyector

      Dont know about c2 software but in my case i run 85% duty cycle on precision 440cc hi impedance(which by the way sucked!) on 22psi and spiking to 91-92% so i switched to denso rx7 turbo hi impedance...
    13. Replies
      2,349
      Views
      343,580

      mk2 coupe pic

      http://i1133.photobucket.com/albums/m590/rodperformance/temporary-2.jpg my never ending proyect !
    14. Replies
      2,349
      Views
      343,580

      oil feed

      Same here mate! Ifh,7 or 8 mm allen for the Plug and walla perfect spot no failures on my turbos related to oil seals or starvation,just warm it up before stomping on it so the oil pressure lowers as...
    15. Replies
      2,349
      Views
      343,580

      spark

      Hi guys!! Just to mention the the rule about heat ranges goes like this!! One heat colder for every 10psi and gap should be the largest without fouling or skiping.but every car is different but for...
    16. Replies
      2,349
      Views
      343,580

      sparkplugs

      Hi there Mr West! I ran bk8e-ix iridium on the pg block and it did idled better but came out all Black so i guess it was to cold for 15psi but looking to run same plugs on -7 temp range!! Great plug...
    17. Replies
      2,349
      Views
      343,580

      8v power!

      Yes the Brazilian guys are running 10 second n\a damn fast.
    18. Replies
      2,349
      Views
      343,580

      hi

      Hi mate I was running 20psi on double stacked gaskets,then the vacuum line to the fpr was unplugged,4th gear pull and messed a almost new rebuild engine!! On single gasket runs great off boost but...
    19. Replies
      2,349
      Views
      343,580

      mr West

      Hi there mate!! 02A is on your near future I foresee!or an o2J.What we are doing is fitting 1.8t gears and 3.68 fd good luck mate
    20. Replies
      2,349
      Views
      343,580

      almost done!

      This took a long time but were getting there!! ABA block and head!
      Ceramic coated piston tops
      550cc injectors out of a turbo 2 rx7
      Turbonetics t3-t4/.48 exhaust 61trim seven blade
      Ms1 v3.0 ecu...
    Results 1 to 20 of 95
    Page 1 of 5 1 2 3 4