Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: bonesaw

    Page 1 of 13 1 2 3 4

    Search: Search took 0.88 seconds.

    1. Thread: it's and ecu's

      by bonesaw
      Replies
      2
      Views
      213

      I personally have done 2 aircooled, ABA and 20v...

      I personally have done 2 aircooled, ABA and 20v all with ITBs with Lugtronic.
    2. Replies
      4
      Views
      232

      follow F1 to see if it goes to alarm module, or...

      follow F1 to see if it goes to alarm module, or clutch switch. it sounds like that is what your issue is.
    3. Replies
      4
      Views
      232

      Is the clutch switch hooked up? The later cars...

      Is the clutch switch hooked up? The later cars have a relay and two long red wires with a green connector that connect to a lime green clutch switch. You may also need to connect a fuse in line...
    4. Replies
      14
      Views
      443

      You will most likely want to just change the...

      You will most likely want to just change the harness. The throttle body has the idle valve built in and 2 more additional wires. It also has the sweep flipped compared to obd1. The engine harness to...
    5. Replies
      14
      Views
      443

      No. You need to use the obd2 engine harness. The...

      No. You need to use the obd2 engine harness. The engine harness and headlight harness are one piece so it is easier to do both. Just dive in. It's fairly simple. Especially that you have two complete...
    6. Replies
      14
      Views
      443

      Only need to do the cluster harness if you want...

      Only need to do the cluster harness if you want entirely plug and play. The turn signal connector for cluster is a black 2 pin and mfa is a signal pin. Purple wire with white stripe. On obd 2 it's a...
    7. Replies
      14
      Views
      443

      You will need to change intake manifold and down...

      You will need to change intake manifold and down pipe. Need to change both the engine harness to fuse panel and harness on actual engine. Will want to swap over possibly headlight and fan harness....
    8. Replies
      4
      Views
      443

      It will work just the wires won't be plug and...

      It will work just the wires won't be plug and play. The obd1 engine harness will have a single connector with purple/white wire. It is not needed. It is for mfa. The turns are also not needed. If not...
    9. Replies
      4
      Views
      443

      Black 2 pin with black/white black/green is to...

      Black 2 pin with black/white black/green is to connect to cluster harness. VR6 OBD1 is 2 pin for turns and 1 pin for MFA
      black 3 pin with black/white black/green is for turns on cluster and purple...
    10. http://www.grimmspeed.com/content/install_guides/m...

      http://www.grimmspeed.com/content/install_guides/manual_boost_controller2.pdf

      Turbo to boost controller. Boost controller to side port of wastegate. Orientation in installation manifold linked...
    11. Depends on internal or external wastegate and...

      Depends on internal or external wastegate and what boost controller.

      Blow off valve run dedicated line from intake manifold. Boost gauge can come off manifold or a T

      The wastegate goes...
    12. Pics might help Where does - thick red/black...

      Pics might help

      Where does
      - thick red/black from dash go to fuse block? - not sure exactly which one you a refering to. pics
      -red/blue yellow plug case go to on fuse block? - z1 power for...
    13. Thread: A2 VR6 FAQ

      by bonesaw
      Replies
      5,612
      Views
      821,154

      Sticky: The g60 one is the same as mk2. So it only works...

      The g60 one is the same as mk2. So it only works with special aftermarket mounts.

      You will need the mount bracket from 02a trans and front motor mount bracket. You will also need to change axle...
    14. Thread: A2 VR6 FAQ

      by bonesaw
      Replies
      5,612
      Views
      821,154

      Sticky: Please read thru thread. You cannot use a b3 k...

      Please read thru thread. You cannot use a b3 k frame. You could use corrado but good luck sourcing one and it is basically same as mk3.
    15. Thread: A2 VR6 FAQ

      by bonesaw
      Replies
      5,612
      Views
      821,154

      Sticky: A3 beam is wider. You can easily swap brakes...

      A3 beam is wider. You can easily swap brakes between beams.
    16. Replies
      12
      Views
      686

      I would loop the head flange to the metal pipe....

      I would loop the head flange to the metal pipe. And then connect coolant ball to metal pipe.
    17. Thread: A2 VR6 FAQ

      by bonesaw
      Replies
      5,612
      Views
      821,154

      Sticky: 2.0 or vr6 k frame works. Bracket needs to be VR....

      2.0 or vr6 k frame works. Bracket needs to be VR. Mounts could be either. Either might need trimming.
    18. Replies
      10
      Views
      479

      Yes

      Yes
    19. Harbor freight

      Harbor freight
    20. Replies
      5
      Views
      585

      Check your grounds.

      Check your grounds.
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4