Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: Stoddart

    Page 1 of 9 1 2 3 4

    Search: Search took 0.78 seconds.

    1. Replies
      2
      Views
      364

      http://forums.vwvortex.com/showthread.php?2975414-...

      http://forums.vwvortex.com/showthread.php?2975414-DIY-Replacing-fuel-injectors-on-a-MKIV-12v-VR6&highlight=fuel+injector
    2. Replies
      2
      Views
      364

      Fuel injector cylinder 3 open

      I ran the vag com on my obd2 and think I have a bad injector does anyone have a DIY for this?
    3. Replies
      1
      Views
      199

      I am looking for remote dyno tuners

      Need professionals for dyno tuning M IV's
    4. Yeah

      You'd might need some very steardy servo's for that.
    5. um...

      if I am correct, if that were the case, I'd be missing on half my cyclinders:confused:
    6. also....

      When I'm reading the faq, it sounds like the ecm can adapt timing. I don't see how; if so, can I flash 'er to the timing that I want?

      original thread......
    7. Ok, now I know that cam position is based off cam...

      Ok, now I know that cam position is based off cam and not the gear. Is there adjustable cam gears for the vr6? I really don't think the generation matters.
    8. Bogs, below 3200

      Idles fine, but at low rpms, you notice the difference when acceleration. if I run 'er above 3200 its sounds fine. I might have a problem with the intake manifold shifter rod tough, bad bushings....
    9. Does anyone make adjustable cam gears for the afp

      The problem I am having is I let a friend drive my car and they downshifted hard into second aroud 40 45 mph. I trashed the guides and jumped some teeth; but, didn't crash the head.

      I've replaced...
    10. this?

      http://forums.vwvortex.com/showthread.php?2105422
    11. Thread: Geometry

      by Stoddart
      Replies
      6
      Views
      884

      geometry is different with vr6

      what's your point?
    12. ECM

      Its been flashed or chipped... taken it to a shop to see if I can re program to oem spec.
    13. Thread: Geometry

      by Stoddart
      Replies
      6
      Views
      884

      Turns out...

      Tie rod end was bad, too. Replaced, BJ's, Links, and Tie Rod Assemblies.

      on another note: Even if your print out for alignment is in spec. this does mean she'll travel strait and narrow. when you...
    14. k,

      So, I would need the euro fog light switch?
    15. Lower brake light, earlier model mkIV, GTI '00

      I had a tail light out on the passenger side and when I went to replace it I realized that there was a lower brake light port right of the reverse light and a snap out clip in the mounting point of...
    16. Replies
      2
      Views
      1,057

      So I created a loop

      So, using Eric Diaz's diagram, I simulated a loop using 3/4 post based off of the diagram. (red +) (black -)
      ...
    17. Replies
      2
      Views
      1,057

      blowing 43

      https://lh6.googleusercontent.com/-viL85pCB6KA/UF5RG7BvU_I/AAAAAAAAAJU/Ntz0lhPS0j8/s681/20120922_185957.jpg
    18. Replies
      8
      Views
      1,338

      thanks diaz

      thanks diaz
    19. Replies
      8
      Views
      1,338

      think

      http://i202.photobucket.com/albums/aa269/cubixy2k/msd2.jpg

      1\6 fire when triggered, bad pack our icm.
    20. Replies
      2
      Views
      1,057

      Msd coilover mkIV

      This is mk 3:
      http://i202.photobucket.com/albums/aa269/cubixy2k/msd2.jpg

      mk iv icm is inverse; ie, mk 3 54321 and mk 4 12345

      so where is my ground, 15?

      which pin? mk 4...
    Results 1 to 20 of 179
    Page 1 of 9 1 2 3 4