Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: AL@PagParts.com

    Page 1 of 13 1 2 3 4

    Search: Search took 0.86 seconds.

    1. Replies
      11
      Views
      408

      No way. I have a GTX2860 and 63 on two different...

      No way. I have a GTX2860 and 63 on two different cars. One for a very active intermediate auto-x guy that had an APR STG3 on there and tiring of the loosening fasteners after every event, swapped...
    2. Replies
      10
      Views
      605

      Also, I find the MFT to be an odd pairing in a...

      Also, I find the MFT to be an odd pairing in a twin scroll housing.... Its almost counterproductive in design and intended purpose...
    3. Replies
      10
      Views
      605

      I would gather that the spooltime variances b/w...

      I would gather that the spooltime variances b/w different A/R's would be rather large b/w the .64ar and .85ar. I dont think the 7163 would spool any slower then the 6758 in the .64ar housing as the...
    4. Replies
      10
      Views
      605

      I have a 7163 here that will be going on a B7...

      I have a 7163 here that will be going on a B7 along with our vbanded turbo kit. We have tested the 6758 w/ the .64ar housing and if the twin scroll spools better then this, I would be shocked as it...
    5. Replies
      158
      Views
      6,096

      I've run them too bill with good success on...

      I've run them too bill with good success on several builds. I always did wonder about them at times as they do seem a bit thin at the bottom taper. But who's to say if there was something to...
    6. Replies
      158
      Views
      6,096

      The single grooved keepers, from my experience,...

      The single grooved keepers, from my experience, are a bit brittle compared to the oem triple. They do not seem to stand up to valvetrain anomalies as I've had them crack in half which resulted in...
    7. Replies
      158
      Views
      6,096

      Not to mention the newest original springs are...

      Not to mention the newest original springs are 10yrs old...
    8. Its not, technically, a bad wheel but its really...

      Its not, technically, a bad wheel but its really not much different in any real aspects other then overall flow from the full sized non cut-down wheel (60mm). I dont notice a measurable difference in...
    9. Replies
      18
      Views
      652

      I would think an aircooled motor would require a...

      I would think an aircooled motor would require a bit more space ;)
    10. Replies
      18
      Views
      652

      I know the spec sheet on some of the older...

      I know the spec sheet on some of the older wiseco's recommend a .0025" wall clearance but that is a bit too tight for me. Spoke to wiseco tech about this while scratching my head looking at the spec...
    11. Replies
      18
      Views
      652

      What I meant is before you start, check your bore...

      What I meant is before you start, check your bore to see if it is within spec before using anything 'drop in'.

      As for piston to wall clearances, i go .0035" on most apps. .004-.005" on high boost...
    12. Replies
      18
      Views
      652

      Nope. Just hone out conservatively but measure...

      Nope. Just hone out conservatively but measure bore first to see if you can get away with it
    13. Replies
      43
      Views
      1,605

      There are no really small housings for the efr...

      There are no really small housings for the efr line. BW's philosophy utilizes comparatively large turbine wheels to offset backpressure. These turbines which are titanium aluminide are sensitive to...
    14. Replies
      43
      Views
      1,605

      You're also running a .48ar vs the EFR's .64ar...

      You're also running a .48ar vs the EFR's .64ar (the T25 EFR is not remotely like the Garrett T25) plus a couple of gears higher (02X 3rd gear is very short as well). There is no way you are spooling...
    15. Absolutely. Its actually a bit easier to deal...

      Absolutely. Its actually a bit easier to deal with then the me7 platform in a lot of ways. We've tuned a local's out on E85, 1200cc injectors with a stock engine (only upgraded rods) to 500awhp. I...
    16. Replies
      43
      Views
      1,605

      No way is the 2867 more responsive then the...

      No way is the 2867 more responsive then the 6758... B7 on base file only

      http://www.pagparts.com/images/efr6758_3rd_gear_pull.jpg

      Its on an FSI which has more displacement and compression so I...
    17. Replies
      43
      Views
      1,605

      Yah, I think the 6758 is leaning more towards the...

      Yah, I think the 6758 is leaning more towards the 30 series. It does use a t25ish flange but the housing for the BW is definitely superior over the internal T25 Garrett housing but NOT your Tial 64ar...
    18. Replies
      43
      Views
      1,605

      I can set you up with a solid base file once its...

      I can set you up with a solid base file once its all sorted
    19. Replies
      43
      Views
      1,605

      These are the new Borg Warner performance line....

      These are the new Borg Warner performance line. The gtx turbos are awesome too and if you want to go that route, the GTX2867 would fit here too. Software would be Eurodyne, yes and prob 630 or 750cc...
    20. Replies
      43
      Views
      1,605

      You can go here: Vband Turbo Kits...

      You can go here:

      Vband Turbo Kits

      and play around with the turbo options on the bottom of the page. One turbo that I have already set up on a few overseas kits is the EFR 6758. Its not on the...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4