Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: acee_dub

    Page 1 of 13 1 2 3 4

    Search: Search took 0.61 seconds.

    1. Must be that rust colour spray job.. I'll get...

      Must be that rust colour spray job.. I'll get someone to rev it tomorrow and see where it's coming from, would be wicked if it isn't the pan, but I see the right side of it is really wet
    2. You mean these? http://i.imgur.com/BQFoFxZ.jpg...

      You mean these?

      http://i.imgur.com/BQFoFxZ.jpg

      http://i.imgur.com/sjy5KqU.jpg
    3. Oil Pan Leaking (Torqued proper + RTV on new gasket)

      I have reinstalled my oilpan with a new gasket, put Permatex Ultra Black on both sides of it and torqued to spec as per bentley, and it is still leaking. Could my bolts be stretched out or should I...
    4. Replies
      8
      Views
      765

      Solved! The problem was that the ignition...

      Solved!

      The problem was that the ignition input capture should have been set to Falling Edge.

      This can be tested for using a tooth logger

      Bad (2 long):
      http://puu.sh/isGxH/3299178402.png...
    5. Replies
      8
      Views
      765

      It seems the desync only occurs between 1100-1300...

      It seems the desync only occurs between 1100-1300 rpms, and if i keep it within that range, it will keep desyncing over and over

      -not noise
      -not dirty sensor
      -not tpsvref voltage

      Tried...
    6. Replies
      8
      Views
      765

      I removed and cleaned the sensor, reinstalled and...

      I removed and cleaned the sensor, reinstalled and retested to no avail.. Checked pin 26 of megasquirt with a multimeter when running and it was getting 4.86v, this value did not change when desyncing...
    7. Replies
      8
      Views
      765

      http://puu.sh/ihusl/9fd054c9c5.png ...

      http://puu.sh/ihusl/9fd054c9c5.png

      http://puu.sh/ihuKv/596e9380ac.png

      http://puu.sh/ihuQM/161d52167f.png

      http://puu.sh/ihv0l/4b59d309de.png

      The trigger log showed desync every time this...
    8. x2 Check for spark / fuel, getting a datalog of...

      x2 Check for spark / fuel, getting a datalog of it cranking helps see whats going on, if you post it up here it helps us to watch the replay of it through megalogviewer (you can make a log through...
    9. Replies
      8
      Views
      765

      SOLVED MS2 v3.0 on 12v VRT (Desyncing @ 1000~ rpm)

      Hi, I just got my VRT running on MS2v3 and have been getting fluctuating RPM / Leaning out when adding throttle gradually from idle (occurs around 1000rpm mark)
      shown in video:

      ...
    10. Replies
      4
      Views
      493

      Sent you a PM Trixy

      Sent you a PM Trixy
    11. Replies
      4
      Views
      493

      Anyone do aluminum welding? (GTA)

      I have a 12v VR6 aluminum intake manifold to which I need to weld a 3" piece of pipe, and a flange to the end of that pipe.
      If anyone does aluminum welding and is willing to do this I can toss you...
    12. Replies
      1
      Views
      504

      figured it out, the steering column shaft had...

      figured it out, the steering column shaft had collapsed, i extended it to the marked position:

      http://puu.sh/awJeO/2f068dd01f.jpg

      http://puu.sh/awJdd/f05639d0d5.jpg
      ...
    13. Replies
      1
      Views
      504

      Steering Rack U-Joint Question (B4/GLX)

      Hi, I had my 98 GLX Jetta ZF steering rack die on me and have swapped in a B4 GLX Passat ZF rack, however I can not get the connecting sleeve over the upper u-joint fully, does anyone know if the B4...
    14. Replies
      18
      Views
      2,752

      The TIP122 was bad, I must have burnt it from all...

      The TIP122 was bad, I must have burnt it from all the re-soldering I was doing upon initial installation.
      Ordered a new one off DigiKey, threw it on, and it is looking good. Next I will need to get...
    15. Replies
      1,430
      Views
      131,460

      Good luck with the swap! :thumbup:

      Good luck with the swap! :thumbup:
    16. Replies
      34
      Views
      6,367

      Poll: Yes :thumbup:

      Yes :thumbup:
    17. Replies
      18
      Views
      2,752

      Suspect that the TIP122 on FIDLE circuit may be...

      Suspect that the TIP122 on FIDLE circuit may be bad.
    18. Replies
      18
      Views
      2,752

      Messing about with it some more, trying to get...

      Messing about with it some more, trying to get the TB to respond.. I could not get response at all.
      I have a good signal going in, similar to the factory except that it is 200hz (factory ecu sends...
    19. Replies
      18
      Views
      2,752

      Set the Idle valve to inverted in settings, did...

      Set the Idle valve to inverted in settings, did not make much difference, however there are no longer negative TPS readings.

      I tried running with Idle Control turned off, it would not idle,...
    20. Replies
      18
      Views
      2,752

      All work is being done on a preheated engine (I...

      All work is being done on a preheated engine (I throw on the factory ECU and let it run to operating temp)
      After updating TunerStudio and MS firmware to the latest I now have two VE tables?...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4