Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: xtremevdub

    Page 1 of 13 1 2 3 4

    Search: Search took 0.95 seconds.

    1. Replies
      1
      Views
      81

      :thumbup:

      :thumbup:
    2. Replies
      951
      Views
      78,692

      I wish I would have seen it before I removed the...

      I wish I would have seen it before I removed the entire fuse box looking for melted wires.. :banghead: And I was looking for that because it died very weirdly.
      First I was running in fumes.. So I...
    3. Replies
      1
      Views
      81

      FS: Audi TT dead pedal in Miami

      Selling an Audi TT dead pedal in great condition. Only one broken tab.
      Goes perfect with the TT pedals if you have them or looks great by itself. Fits all MK4's.


      $50 SHIPPED to the lower 48...
    4. Replies
      951
      Views
      78,692

      Today I decided to spend some time trying to...

      Today I decided to spend some time trying to figure out why mine died about a month ago in the middle of a bridge in the pouring rain..
      after a few hours of disconnecting and inspecting every wire...
    5. See if pin 24 on your ECU throws a signal when...

      See if pin 24 on your ECU throws a signal when you open ignition. The computer turns on the fuel pump relay and from there it goes to the fuel pump.
      Could be your ECU.
      ...
    6. This is not correct.. the pump primes even if the...

      This is not correct.. the pump primes even if the car doesnt run.. Or at least is supposed to.
      To the OP, turn the ignition switch on and listen if the pump starts working for a couple of seconds....
    7. Replies
      951
      Views
      78,692

      You can use the tool to press it out or hammer it...

      You can use the tool to press it out or hammer it out.. I prefer the last method.

      When you modify the HF tool, you end up using the 72mm tool and making it a tad smaller.. 72mm is the same size as...
    8. Replies
      951
      Views
      78,692

      That method takes too many tools that you have to...

      That method takes too many tools that you have to "make" and it pushes the bearing back in by pressing the center of the bearing, which can ruin it easily. Plus it is very time consuming.
      Do you...
    9. Replies
      1,587
      Views
      459,593

      you have more pics of the motor??? that looks...

      you have more pics of the motor??? that looks great :thumbup:
    10. Replies
      5
      Views
      133

      Is for a g60, but I dont think it makes much o a...

      Is for a g60, but I dont think it makes much o a difference.
      got pics?
    11. Replies
      5
      Views
      133

      WTB headlight hanesses

      http://www.a2resource.com/electrical/images/CE2.gif

      A1 and A2 from the fuse box forward. Uncut.
      Let me see what you have you Corrado killers. :P
    12. Danny, Did you ever send me those longer bolts?...

      Danny,
      Did you ever send me those longer bolts?
      Cant wait to install these. :thumbup:
    13. If you get passat b3 parts, they can swap to the...

      If you get passat b3 parts, they can swap to the Corrado.. pedals, clutch, flywheel, starter, you get the idea.
      you will need this when the time comes.....
    14. ok.. last freebie.. (1).. the VR6 tranny were...

      ok.. last freebie..

      (1).. the VR6 tranny were shifted by cables. like the Corrado G60 trannies. And their clutches were hydraulic unlike the ABA transmissions that were rod shifted and had a...
    15. the engine will fit. You will need the full...

      the engine will fit. You will need the full engine harness from the mk3 aba car as well and you will need to splice it and connect it to the corrado harness.. (mostly lights, hi/low, fogs and horns)...
    16. I recently put a new pump on the car and can go...

      I recently put a new pump on the car and can go to empty without issues.. the pumps inside have rubber diaphrams that when they are old, they disintegrate causing the pick up area not to work unless...
    17. You got pm:thumbup:

      You got pm:thumbup:
    18. Replies
      951
      Views
      78,692

      Since you had both pieces out, you could have...

      Since you had both pieces out, you could have taking it to a place that does weld and have it done for like $20.. less headaches down the road.. :thumbup:
    19. Replies
      951
      Views
      78,692

      Why didnt you just weld that neck to the rad and...

      Why didnt you just weld that neck to the rad and called it a day?
    20. Replies
      20
      Views
      762

      You dont need to change the k frame, just the...

      You dont need to change the k frame, just the front x-member to use the hockey pucks. Your problem is the front not the back.
      You could also keep your x member and go solid mount.
      Bfi and bbm...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4