Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: 98GTI_VR6

    Page 1 of 13 1 2 3 4

    Search: Search took 0.54 seconds.

    1. The clip isn't in the pedal correctly somehow and...

      The clip isn't in the pedal correctly somehow and won't let it I think somewhere down the line of owners that pedal got messed up inside of where the clip into the spring maybe another concern too...
    2. pedal

      I think the pedal arm is messed up I have like 1 inch of play b4 the master even starts moving. Main problem is clutch isn't fully disengaging.
      1998 gti vr6 ,
      Where the master connects to the pedal...
    3. any sell a new clutch pedal arm assembly

      My clutch pedal is missing or,broke the plastic female piece that the master clips into and now has a lot of,play and won't disengage fully
    4. ? anyone mAke a kit to mount E spec turns dummies fogs in us bumper

      Any diy available for mounting the ecs tuning E spec turns with the fogs and dummies?
    5. still selling it

      Hey im located in florida are you still selling the jetta?
    6. I'm Gona be gettin some 268's here soon lookin...

      I'm Gona be gettin some 268's here soon lookin for a nice set of used ones
    7. Updating my build...... Displacement or...

      Updating my build......


      Displacement or Bore:3.0L

      Managment:BFI chip stg. 2 cam profile

      Internals:arp hardware, hd valve springs, wiseco pistons

      Comp Ratio: 11:1
    8. Replies
      23
      Views
      915

      I'll buy them if u still have them dec 1st for...

      I'll buy them if u still have them dec 1st for 500$
    9. Do u still have the lower intake manifold with...

      Do u still have the lower intake manifold with rail, fpr, and injectors?
    10. My buddy is doing it to a 350z fully built vrt he...

      My buddy is doing it to a 350z fully built vrt he is the creater of the kit, if all goes well it's my turn
    11. Replies
      29
      Views
      2,729

      I have bfi stg 2 cam profile chip with autotech...

      I have bfi stg 2 cam profile chip with autotech 262's with a 3.0 bottom end and lots of head work pp. ECt n doing over 200 whp na, any1 know if I got drc 268's if I'd have to get a new chip?
    12. Not bad in cost, I already have the motor I just...

      Not bad in cost, I already have the motor I just need the 300$ adapter with motor mounts (motor side) and a 350z transmission and everything else like mega squirt n junk 2000$ project
    13. What do u think of doing a vr6 swap to a 1967 Datsun pickup?

      ????? I wanna do it using my friends adapter plate for a 350z trans (6 speed vr6 67 Datsun single can pickup) sexy time
    14. Update my vehicle

      Starting off saying this thread=badass
      I just recently swapped my 2.8 for a built 3.0 wiseco piston engine I got off a buddy for like 500$ and took my lw flywheel out n replaced it with the stock...
    15. Fixed it but found 3 had backed out and 1 snapped...

      Fixed it but found 3 had backed out and 1 snapped off inside I just went to ace after getting bolt specs from dealer and used lock washers no loctite, loctite sux to take back off I only Use it on...
    16. Ok thank u:thumbup:

      Ok thank u:thumbup:
    17. Tryin to find a source before getting bent over...

      Tryin to find a source before getting bent over and raped by vw for 4 bolts like any regular site carry stuff like that? Or can someone give me the exact bolt sizes so I can go to ace hardware
    18. Rear motor mount bolts to block backed out

      My engine is now cocked left and 3 or more of the bolts that hold the rear mount alluminum bracket to block somehow backed themselves all the way out while driving, where can I purchase these four...
    19. It moved

      Moved to the parking lot behind bennet auto on hybiscus like where adult Ed is!
      Also there's car show around 6 at 5 guys at the new palm bay mall
    20. Replies
      4
      Views
      426

      To make the tap not so loud

      Thicker oil is better if I was having a clearance issue I started the build with 5w 40 and then had a tap and changed the oil to thicker stuff to hopefully prevent damage
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4