Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: sdezego

    Page 1 of 13 1 2 3 4

    Search: Search took 0.77 seconds.

    1. Replies
      114
      Views
      7,220

      haha, nice. I know the feeling. Definitely...

      haha, nice. I know the feeling.

      Definitely coming together. I like your ramps :)
    2. Replies
      5
      Views
      352

      You likely burnt a hole in a piston, so...

      You likely burnt a hole in a piston, so compression is going into crank case.
    3. Replies
      19
      Views
      1,019

      If it rocks, then 99% it is the Rubber Front...

      If it rocks, then 99% it is the Rubber Front guide (bottom right in your pic). ..but might as well replace them all at once.
    4. Replies
      13
      Views
      965

      This may help you decide....

      This may help you decide. http://www.dubforce.net/forums/index.php?showtopic=5994

      If you plan on hitting nitrous, I would definitely go with 5's
    5. Replies
      19
      Views
      1,019

      Stock Heated Seat element wiring repair (very...

      Stock Heated Seat element wiring repair (very common failure point and easy fix)

      http://www.corrado-club.ca/forum/viewtopic.php?t=5304
    6. Replies
      19
      Views
      1,019

      I believe this is the link to the site that the...

      I believe this is the link to the site that the guy purchased the aftermarket heaters from. Still looking for the thread.

      http://www.heaterseat.com/products.php
    7. Replies
      19
      Views
      1,019

      Yes. There was an old thread on it, but not sure...

      Yes. There was an old thread on it, but not sure I have it handy.

      One thing I can tell you is that if your Stock heater(s) are not working it is a simple fix and does not require the seats to...
    8. Replies
      654
      Views
      141,708

      Last few months have been extremely busy, so no...

      Last few months have been extremely busy, so no time to even look at it (other than acquire a few parts here and there).

      My Durango's Auto Trans is still apart in my garage with all of the new...
    9. Replies
      9,992
      Views
      490,776

      Make sure hood is in perfect adjustment before...

      Make sure hood is in perfect adjustment before removing.
      Take sharp scribe or mechanics pick and carefully scribe light line around bolt heads on hinge to hood
      remove bolts on hinge to hood (...
    10. Replies
      13
      Views
      965

      Looks like it will be fun :cool:

      Looks like it will be fun :cool:
    11. Yes, I remember the car (kind of) and even had...

      Yes, I remember the car (kind of) and even had the magazine at one point. However, I thought it was a Scirocco2 and a bit earlier than the Corrado, but I could be wrong

      I remember the wheel...
    12. To re-iterate what I mentioned above, you don't...

      To re-iterate what I mentioned above, you don't need that brass banjo and bolt setup if you use the aftermarket VDO sender that has 2wires/2 terminals (1 for the low pressure oil light, and one for...
    13. No, you need the VDO Gauge Sender which is a much...

      No, you need the VDO Gauge Sender which is a much larger unit. The Factory used a brass Banjo fitting that the gauge sender screwed into and then the Oil Pressure Light sender (what you have...
    14. Something definitely sounds off with your colors....

      Something definitely sounds off with your colors. Can you post what you have? Blue/green should be HVAC related, but maybe you have the whole "N" Fuse panel connector??
    15. Replies
      6
      Views
      387

      ^This. It is a muffler/baffle. If you look...

      ^This. It is a muffler/baffle. If you look inside is is basically a bunch of staggered disks designed to quit noise/resonance on the low side. Also, not just sealer, but if the compressor ever...
    16. Replies
      3
      Views
      348

      My daughter has a competition, so I won't be able...

      My daughter has a competition, so I won't be able to make it.
    17. Replies
      50
      Views
      6,955

      Very nice as usual.

      Very nice as usual.
    18. Replies
      3
      Views
      945

      1 - 12v to Ign coil or alike (keyed) 2 - Signal...

      1 - 12v to Ign coil or alike (keyed)
      2 - Signal
      3 - Grnd

      Run Signal to pin T27 on the T28 Cluster plug (or via U1/11 - G1/11)
    19. Yes, this is correct. However, I usually see the...

      Yes, this is correct. However, I usually see the bearings wear out quickly more so than wearing out the crank. Have they checked it with a new set of 4 pcs bearings and new thrust shims?

      For...
    20. Replies
      7
      Views
      486

      Wire wheel for the valves (preferrably brass). ...

      Wire wheel for the valves (preferrably brass).

      it will take a little elbow work, but Berryman B12 is the stuff to use...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4