Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: huichox4

    Page 1 of 13 1 2 3 4

    Search: Search took 0.69 seconds.

    1. Replies
      7
      Views
      392

      FX400 from streetwerke was the same as the normal...

      FX400 from streetwerke was the same as the normal fx 400 only that streetwerke only used clutches that were built to tighter tolerances I was told. For example assume that CM has a +- 3mm tolerance,...
    2. Thread: Head Swap

      by huichox4
      Replies
      4
      Views
      256

      if you get the bare mk5 head and swap everything...

      if you get the bare mk5 head and swap everything from the mk4 you should be just fine. if you are using mk5 timing stuff the exhaust cam and timng sproket are different, so I believe and you need to...
    3. Replies
      295
      Views
      29,186

      sweet man. now put the engine back together and...

      sweet man. now put the engine back together and make some noise
    4. if the pipes are off the car you will rip the...

      if the pipes are off the car you will rip the flex joint of them. you could try to bolt them back to your cat pipe and hold it like that so the flex joints wont move or put a big pry bar inside...
    5. Replies
      97
      Views
      7,395

      HPA DTM 7670 Initial Review

      well yeah most of the oil/coolant lines if they are banjo fittings with crush washers just tight but dont go too tight, if they leak give it an extra nudge.
      You can look up the recommended torque...
    6. Replies
      269
      Views
      26,729

      Also got my ptp new heat blanket installed....

      Also got my ptp new heat blanket installed. Forgot to take pics before installing it but here is one after everything is back on the car. Just need to wrap the wastegate dump for the heat protection...
    7. Replies
      97
      Views
      7,395

      I think you might end up having issues with...

      I think you might end up having issues with swapping sides. I had them swapped (you have to modify the plugs for them to work) and was getting errors too. I believe that the length of the wire...
    8. Replies
      6
      Views
      197

      most likely condensation in the exhaust and not...

      most likely condensation in the exhaust and not in the intake. In the remote case it is water in the combustion chamber it might be from coolant and your head gasket is blown but the smoke would have...
    9. Replies
      269
      Views
      26,729

      Same ****ty AN fittings as in the bay are used in...

      Same ****ty AN fittings as in the bay are used in the surge tank on the back of the car. Just finished welding the last fitting this week will finish wiring the pumps and assembling the last few...
    10. Replies
      417
      Views
      61,286

      That awesome!! What radiators are those?

      That awesome!! What radiators are those?
    11. Replies
      10,974
      Views
      769,601

      What did you do to your .:R today?

      http://img.tapatalk.com/d/14/08/17/ypa3e2u4.jpg

      Took her on a little ferry trip ..... vw r32 Jetta wagon

      And a buffalo got his head almost stuck in the window
      ...
    12. Replies
      4
      Views
      302

      Thanks !!

      Thanks !!
    13. you can remove the rubber snake from the rain...

      you can remove the rubber snake from the rain tray when you take it to the track instead or in addition of spacers that opens a little gap already.
    14. Replies
      4
      Views
      302

      I'll take the box, sent you a PM

      I'll take the box, sent you a PM
    15. Replies
      269
      Views
      26,729

      final product on the engine bay ...

      final product on the engine bay

      http://img.tapatalk.com/d/14/08/15/dy7a6ada.jpg

      Finished all fuel lines and vacuum lines on the bay plus cut up a touareg exhaust heat shield to fit over the...
    16. yes, it all depends how much you push it mine has...

      yes, it all depends how much you push it mine has been good several times and bad a few others. Do you track your cars often? just do your normal track prep plus a bit extra work on getting more air...
    17. Replies
      10,974
      Views
      769,601

      http://img.tapatalk.com/d/14/08/15/dy7a6ada.jpg ...

      http://img.tapatalk.com/d/14/08/15/dy7a6ada.jpg

      Finished all fuel lines and vacuum lines on the bay..... Finally. Now the rest of the car needs put together
    18. Replies
      295
      Views
      29,186

      I guess its about time... Turbo Build.

      Psi has nothing to do with it, it is cfm and how much volume of air the turbo moves. 1.8t stock turbo puts down 22-24 psi with just adding a chip to the car, but put a gt35 on it at 15 psi and you...
    19. Replies
      295
      Views
      29,186

      the GT35 was the old turbo, now I have a T4 6265...

      the GT35 was the old turbo, now I have a T4 6265 (forgot to mention it was a T4) with a bigger manifold and wastegate. 3" straight through exhaust. didnt go above 14-16 psi (wastegate pressure)...
    20. Replies
      295
      Views
      29,186

      No, just stock head when that happened, when I...

      No, just stock head when that happened, when I was running the GT3582R T3 ar 1.25 23psi, then 6265 bb ar.68 and switched to an ar .8X or .9x I cant recall now at 14-16 psi when manifold and turbo...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4