Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: Campbell

    Page 1 of 13 1 2 3 4

    Search: Search took 0.69 seconds.

    1. Replies
      5
      Views
      400

      Ugh, I have no problem with the mechanical...

      Ugh, I have no problem with the mechanical aspects of installing this.. circuit boards and stuff like that psych me out!

      In reading the Patatron diagram versus a standard MS1 2.2. diagram on the...
    2. Replies
      5
      Views
      400

      Further on this thread - I have a Patatron MS1...

      Further on this thread - I have a Patatron MS1 2.2 unit I am installing, the car already has an Electromotive ignition set up that I am leaving in place. That is why I'm not using the ignition...
    3. That is my issue, the one I have fits over a ball...

      That is my issue, the one I have fits over a ball fitting and the passat TB needs the kind with a ball shaped plug on the end. The TB hardware on each is completely different. Was hoping someone had...
    4. Passat throttle body - Megasquirt - what accelerator cable

      Hi - converting an 1987 Scirocco to Megasquirt and am using a Passat throttle body with TPS. Question, anyone know what accelerator cable will work or how to modify a cable to work? thanks
    5. Replies
      0
      Views
      165

      Fuel Injectors

      I am going to install a megasquirt system in a MK1 JH and have a chance to get some new Magneti Marelli injectors (IWP069) but they are only 47mm long and the bosch injectors are 75mm, has anyone...
    6. Replies
      0
      Views
      181

      Magneti Marelli Fuel Injectors

      I am going to install a megasquirt system in a MK1 JH and have a chance to get some new Magneti Marelli injectors (IWP069) but they are only 47mm long and the bosch injectors are 75mm, has anyone...
    7. Replies
      2
      Views
      241

      Thanks

      Thanks
    8. Replies
      2
      Views
      241

      16v PL engine oil squirter screws

      I need to get a few of the torx screws that hold the oil squirters in place, does anyone know the part number or where to get them? thanks
    9. Replies
      5
      Views
      400

      MS1 2.2 ignition

      I am going to be installing a MS1 2.2 unit to control fuel but not spark. The unit us set up to control ignition, should I just not hook up the ignition control wire or is it best to jump it out in...
    10. Replies
      5
      Views
      366

      I went through it again, the ball joints and tie...

      I went through it again, the ball joints and tie rod ends are okay. The tie rod has 1/8" movement in and out of the knuckle it goes into before the steering gear. There is no movement from the...
    11. Replies
      5
      Views
      366

      Thanks, I will look for that in the morning. Is...

      Thanks, I will look for that in the morning. Is the nut towards the steering wheel or on the wheel side? thanks again
    12. Replies
      5
      Views
      366

      Power Steering Rack

      My daughter was home today complaining about highway shimmy with her 1987 Scirocco 8v automatic. I was checking for bad ball joints or tie rod ends and found.. the passenger side steering rod had...
    13. Replies
      1
      Views
      388

      Got it! tried again to get it out with a hex and...

      Got it! tried again to get it out with a hex and simply rounded it out. Then started with a very small left hand bit and drilled into the stud, then a larger drill bit and then a larger drill bit...
    14. Replies
      1
      Views
      388

      Stripped oil squirter screw

      Hi - could use some ideas, am refreshing a 16v PL block and one of the oil squirter torx screws is stripped.. any suggestions on how to get it out? definitely don't want to mess it up. It is so tight...
    15. Replies
      4
      Views
      544

      Thanks!

      Thanks!
    16. Replies
      4
      Views
      544

      Jim, how does the sprocket on the end of the oil...

      Jim, how does the sprocket on the end of the oil pump stay in place? can it be used on a 8v? the oil pumps look the same for 8v and 16v.. thanks
    17. Replies
      4
      Views
      544

      Noob question on oil pumps

      How does the oil pump work on 16v engines? I know on 8v engines the intermediate shaft turns the distributor which also turns the oil pump. But the 16v set up is different, how does the oil pump get...
    18. Replies
      1
      Views
      194

      sold

      sold
    19. Replies
      1
      Views
      212

      sold

      sold
    20. Replies
      1
      Views
      212

      FS: Ball Joint Extenders

      For sale, 50mm (2") ball joint extenders, 19mm. Installed but not used - changing the set up. $100 shipped in the U.S. Thanks

      Would post a pic but don't know how..
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4