Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: zero.

    Page 1 of 13 1 2 3 4

    Search: Search took 0.90 seconds.

    1. Thread: Need help asap!

      by zero.
      Replies
      10
      Views
      260

      What year is it? If it's OBD1, there is no...

      What year is it? If it's OBD1, there is no alignment, but there is an idle adjustment screw. On OBD2 you can do the alignment with VCDS...
    2. Replies
      11
      Views
      320

      Sounds like it's for one of the horns. There...

      Sounds like it's for one of the horns. There should be two on the passenger side. The bracket on the lower one tends to rust out if you live in a climate with snow and may have been removed at some...
    3. Replies
      5
      Views
      205

      True, but I've never seen an 01M in an OBD1...

      True, but I've never seen an 01M in an OBD1 still. Must have been a unicorn thing to work with OBD1 electronics and mechanical TB. I've seen a couple people say they had an 01M in an OBD1, but the...
    4. Replies
      14
      Views
      374

      There were certainly early models with airbags....

      There were certainly early models with airbags. Came with this steering wheel:
      http://img.photobucket.com/albums/v601/dubsnmotion/IMG_0867.jpg

      The non-airbag wheels only came in OBD1 models from...
    5. Replies
      5
      Views
      205

      If it's OBD1, it will have a dipstick. If it's...

      If it's OBD1, it will have a dipstick. If it's OBD2, there is no easy way to check the level other than dropping the pan and loosening the red/orange plastic drain plug to see if oil comes out. You...
    6. Sounds like some valve chatter. Try to pinpoint...

      Sounds like some valve chatter. Try to pinpoint where the sound is coming from. It could just be something loose rattling. Changing a valve cover gasket isn't rocket science. I'm assuming you changed...
    7. Replies
      12
      Views
      394

      Since it's a 94, you should take a look at the...

      Since it's a 94, you should take a look at the idle stabilizer valve and clean it. It might be sticking.
    8. Replies
      0
      Views
      97

      WTB: Passenger Headlight

      Looking for a good condition passenger headlight with working adjusters. PM price shipped to 18618. Thanks
    9. Replies
      15
      Views
      473

      That's what I was thinking it was when you said...

      That's what I was thinking it was when you said blue because that's what Autozone will give you if you buy their manager special oil change package with the pan, funnel, 5 quarts, towels, hand...
    10. Replies
      15
      Views
      473

      Sounds like they were both cheap filters. I...

      Sounds like they were both cheap filters. I usually always use Mann or Mahl and order by the case. I've never had problems using cheap filters when I do run them with MMO or Sea Foam, but others...
    11. Not much that would cause it to smoke unless...

      Not much that would cause it to smoke unless there's a short. I'd clean up the terminals, grounds under the battery tray, as well as the wiring to the starter and alternator. If it's clicking when...
    12. Just throwing this out there, but you also need...

      Just throwing this out there, but you also need to pay attention to how the inner tie rods thread on the rack. Both ZF and TRW racks have internal and external threaded options. Most I've seen have...
    13. The only problem with not burping at all is that...

      The only problem with not burping at all is that method wouldn't work well if there was air trapped in the heater core hoses, which is pretty common and leads to little or no heat. You'll only get it...
    14. Replies
      4
      Views
      160

      Most likely just the difference between heated...

      Most likely just the difference between heated and non-heated. Guessing the ones originally in your car were heated and you're trying to swap non-heated. They should have a part number on them. There...
    15. If your heat takes awhile to warm, it could be...

      If your heat takes awhile to warm, it could be air still or a bad resistor on your heater core, but more commonly, the blend door is bad and just letting cold air in (common sign is foam coming out...
    16. Maybe not exact time frame of driving, but I've...

      Maybe not exact time frame of driving, but I've experienced this exact symptom after coolant flushes when not properly burping. Temp will rise up and then drop back down once the air bubbles move....
    17. Make sure there's no air in the system. It's...

      Make sure there's no air in the system. It's pretty common to overheat after doing any work on the coolant system due to air being trapped and not properly burping. It's the easiest thing to try...
    18. Replies
      21
      Views
      621

      Price isn't too bad then I guess. You can still...

      Price isn't too bad then I guess. You can still get every single piece and all the hardware right down to the end rivets from dealers for around $725. ECS has everything too, except for the washers,...
    19. Replies
      21
      Views
      621

      Do these include the protective film strips?

      Do these include the protective film strips?
    20. Replies
      22
      Views
      6,674

      If they are the stick ons, you should be able to...

      If they are the stick ons, you should be able to find them easy. Clip-ons might be a little harder to find, but I've found numerous sets at the yard I go to and have sold the whole set with new clips...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4