Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: Mr.loops

    Page 1 of 13 1 2 3 4

    Search: Search took 0.71 seconds.

    1. Replies
      17
      Views
      641

      That was the result you got when the DVOM was...

      That was the result you got when the DVOM was attached from battery positive to starter 50 (with it still connected to the starter and back probed) while cranking?

      The reason I ask is a lot of...
    2. Replies
      17
      Views
      641

      Now we know it's not a starter issue. Time to...

      Now we know it's not a starter issue. Time to trace the wire backwards to the ignition switch. Start here. With your one of your leads of the DVOM connected to battery positive and other back...
    3. Replies
      2
      Views
      243

      I would recheck the linkage to make sure it is...

      I would recheck the linkage to make sure it is functioning correctly. Additionally, confirm that your transmission mount bolt is good a tight.
    4. Replies
      5
      Views
      437

      Your being a little rough on the guy don't you...

      Your being a little rough on the guy don't you think? This wasn't your typical "My car won't start, please help" thread where absolutely no additional information or effort was put into diagnosing...
    5. Replies
      1
      Views
      247

      I would get your car up to operating temp to help...

      I would get your car up to operating temp to help speed up evaporating process of any water that might have worked its way down the clutch area. With your engine still running, have a go through all...
    6. Replies
      7
      Views
      368

      There is a wealth of information on his site. ...

      There is a wealth of information on his site. Keep in mind Broke deals primarily with 020 boxes, however, yours will be a 02J transmission and will require a only a 6mm allen to remove the drive...
    7. Replies
      1
      Views
      205

      There are "newer" boxes out there that would be...

      There are "newer" boxes out there that would be compatible with your car. Two examples are DFQ, CHE transmission codes.

      I'm not sure, but your Cabby might have 90mm flanges where the two boxes I...
    8. Replies
      12
      Views
      418

      That's it! If the 5th gear housing is leaking...

      That's it!

      If the 5th gear housing is leaking then I would replace it with a new end cap gasket. Otherwise leave it alone. I would closely inspect this one as well:...
    9. Replies
      12
      Views
      418

      Inspect your input and rear main seal for any...

      Inspect your input and rear main seal for any signs of leakage


      Sent from my iPhone using Tapatalk
    10. Replies
      3
      Views
      318

      That round connector should be installed on the...

      That round connector should be installed on the threaded post with the appropriate nut


      Sent from my iPhone using Tapatalk
    11. You need GL-4 Sent from my iPhone using...

      You need GL-4



      Sent from my iPhone using Tapatalk
    12. Replies
      3
      Views
      307

      020 fifth gear separation from hub

      There are 3 thongs the need to be depressed before the assembly ( thrust washer) can be removed off the hub.

      What works for me is while depressing one tong I'll use a small flat blade screwdriver...
    13. The tool part number is VW 3059. There are quite...

      The tool part number is VW 3059. There are quite a few suppliers out there that will have it. I believe autotech or ECS tuning will have the best pricing.
    14. Replies
      7
      Views
      548

      Talk to either HGB or Broke for the parts you...

      Talk to either HGB or Broke for the parts you need. Alternately you can contact these guys for help: http://www.zelek.com/
    15. Throw that gasket in the garbage, you just need...

      Throw that gasket in the garbage, you just need the o- ring for this engine :)


      Sent from my iPhone using Tapatalk
    16. Replies
      5
      Views
      660

      To me that looks like either your coolant flange...

      To me that looks like either your coolant flange is leaking or your low pressure oil pressure sensor is the culprit




      Sent from my iPhone using Tapatalk
    17. Did you exceed the oil capacity for this...

      Did you exceed the oil capacity for this transmission?

      Certainly too much oil could cause you some leaking issues.


      Sent from my iPhone using Tapatalk
    18. Replies
      3
      Views
      301

      Yes definitely a good idea to mark all the wires...

      Yes definitely a good idea to mark all the wires :)

      The CE fuse box ports are all identified either with a letter or with a letter and number. Additionally, most of them have their own unique...
    19. Replies
      3
      Views
      301

      There are two slide bars on the fuse box that...

      There are two slide bars on the fuse box that must be pulled back (out) before each terminal can be removed


      Sent from my iPhone using Tapatalk
    20. Thomas did a video for a hall sensor replacement...

      Thomas did a video for a hall sensor replacement for a A2 engine (will be the same as your A3): https://www.youtube.com/watch?v=CkPwC_kdLmU&list=UUm3WosFt2A-Z1P436Fkjfxw
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4