Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: Campbell

    Page 1 of 13 1 2 3 4

    Search: Search took 0.89 seconds.

    1. Replies
      2
      Views
      130

      Thanks

      Thanks
    2. Replies
      2
      Views
      130

      16v PL engine oil squirter screws

      I need to get a few of the torx screws that hold the oil squirters in place, does anyone know the part number or where to get them? thanks
    3. Replies
      1
      Views
      162

      MS1 2.2 ignition

      I am going to be installing a MS1 2.2 unit to control fuel but not spark. The unit us set up to control ignition, should I just not hook up the ignition control wire or is it best to jump it out in...
    4. Replies
      5
      Views
      335

      I went through it again, the ball joints and tie...

      I went through it again, the ball joints and tie rod ends are okay. The tie rod has 1/8" movement in and out of the knuckle it goes into before the steering gear. There is no movement from the...
    5. Replies
      5
      Views
      335

      Thanks, I will look for that in the morning. Is...

      Thanks, I will look for that in the morning. Is the nut towards the steering wheel or on the wheel side? thanks again
    6. Replies
      5
      Views
      335

      Power Steering Rack

      My daughter was home today complaining about highway shimmy with her 1987 Scirocco 8v automatic. I was checking for bad ball joints or tie rod ends and found.. the passenger side steering rod had...
    7. Replies
      1
      Views
      356

      Got it! tried again to get it out with a hex and...

      Got it! tried again to get it out with a hex and simply rounded it out. Then started with a very small left hand bit and drilled into the stud, then a larger drill bit and then a larger drill bit...
    8. Replies
      1
      Views
      356

      Stripped oil squirter screw

      Hi - could use some ideas, am refreshing a 16v PL block and one of the oil squirter torx screws is stripped.. any suggestions on how to get it out? definitely don't want to mess it up. It is so tight...
    9. Replies
      4
      Views
      518

      Thanks!

      Thanks!
    10. Replies
      4
      Views
      518

      Jim, how does the sprocket on the end of the oil...

      Jim, how does the sprocket on the end of the oil pump stay in place? can it be used on a 8v? the oil pumps look the same for 8v and 16v.. thanks
    11. Replies
      4
      Views
      518

      Noob question on oil pumps

      How does the oil pump work on 16v engines? I know on 8v engines the intermediate shaft turns the distributor which also turns the oil pump. But the 16v set up is different, how does the oil pump get...
    12. Replies
      1
      Views
      180

      sold

      sold
    13. Replies
      1
      Views
      195

      sold

      sold
    14. Replies
      1
      Views
      195

      FS: Ball Joint Extenders

      For sale, 50mm (2") ball joint extenders, 19mm. Installed but not used - changing the set up. $100 shipped in the U.S. Thanks

      Would post a pic but don't know how..
    15. Replies
      1
      Views
      180

      FS: Ball Joint Extenders

      For sale, 1.75" ball joint extenders, 19mm. Installed but not used - changing the set up. $100 shipped in the U.S. Thanks

      Would post a pic but don't know how..
    16. Replies
      22
      Views
      1,147

      Well I can't handle the vibration... I have a...

      Well I can't handle the vibration... I have a heavy duty rubber mount for the transaxle - I put all these mounts in when I had the engine out, what is the best way to change just the transaxle mount?...
    17. Replies
      0
      Views
      253

      MK2 Disc Brake Clips

      Hi, I need 2 sets of the front disc brake clips that hold the pads in place.. just let me know what you want for them.

      Thanks
    18. Replies
      22
      Views
      1,147

      Thanks for the info, there is a startling amount...

      Thanks for the info, there is a startling amount of vibration...
    19. Replies
      22
      Views
      1,147

      Solid Mounts...

      I just put a solid front mount on, a solid BS stage 2 urethane tranny mount on and the prothane urethane insert in the passenger side rear engine mount. Can someone who has done this describe how...
    20. Replies
      3
      Views
      215

      Still looking...

      Still looking...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4