Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: zrau17

    Page 1 of 13 1 2 3 4

    Search: Search took 0.80 seconds.

    1. Replies
      4
      Views
      189

      Dood you can see where it goes in the friggin...

      Dood you can see where it goes in the friggin picture you took lol.

      All thats for is the secondary air system. Basically for emissions is pulls some air and pumps it out into the EGR valve and...
    2. Replies
      4
      Views
      256

      Google how to align the shift linkages, there's a...

      Google how to align the shift linkages, there's a video by DieselGeek that does a great job explaining it. Also, wouldn't hurt to give it a trans fluid change.
    3. Replies
      13
      Views
      561

      Make sure the strut bolts are tight on the...

      Make sure the strut bolts are tight on the spindles. How did you tighten the upper strut nuts? If those are the slightest bit loose they'll clunk. One thing I've noticed in the past, is if when...
    4. Replies
      13
      Views
      453

      You shouldn't really have to force it off hard...

      You shouldn't really have to force it off hard enough to move either gear really. If it does, should you have done your previous work well enough and marked the belt etc. getting it back on shouldn't...
    5. More than likely lol, I drove static very low for...

      More than likely lol, I drove static very low for a long time with a six speed and never had a problem. I can "drive" my car (meaning it'll roll lol) aired out in the front and the axles still don't...
    6. Replies
      6
      Views
      272

      I was pretty sure the TT and OEM ball joint taper...

      I was pretty sure the TT and OEM ball joint taper was the same and so was the pattern for the three bolts. Why not get ahold of one and measure the tapered part at the top, and about a half an inch...
    7. Get a six speed.

      Get a six speed.
    8. Replies
      33
      Views
      861

      Holy ****, care to share what numbers it made to...

      Holy ****, care to share what numbers it made to do that?

      As mentioned, 6-bolt crank pulley and damper :thumb up: , one of the small things I've wanted to do but haven't run into a need for it...
    9. Replies
      1
      Views
      153

      You may get a lot of mixed answers with this....

      You may get a lot of mixed answers with this. Some guys prefer small port, some prefer large port. Overall you have more volume with the large port, which is good for spool…but you also have a...
    10. Thread: Yo dawg

      by zrau17
      Replies
      5
      Views
      244

      Timeout lol, no way you're getting both in there....

      Timeout lol, no way you're getting both in there. I couldn't fit a door in my 2 door. A hatch might fit. These people just told you what fit in their four doors, you do not have a four door. If ou go...
    11. Replies
      8
      Views
      409

      Port on the head? The thermostat flange is not on...

      Port on the head? The thermostat flange is not on the head.
    12. If you want to go to this extent and remove...

      If you want to go to this extent and remove everything, there's people that have had good luck taking the manifold and turbine housing to a machine shop and having them milled perfectly flat and...
    13. Get another stock clutch. Why change anything if...

      Get another stock clutch. Why change anything if stock is sufficient?
    14. Replies
      2,625
      Views
      191,271

      lmao you still do this?

      lmao you still do this?
    15. Replies
      0
      Views
      365

      4 cylinder 02M, 4 and 6 knock...

      Just yesterday, or last night really...I left a friends and once I got to fourth gear started hearing a loud clacking noise. It's rpm related, seems that only 4 and 6 do it. Every other gear is...
    16. Replies
      33
      Views
      2,281

      I've used these,...

      I've used these, http://store.034motorsport.com/8mm-copper-plated-steel-lock-nut-m10-wrench-head.html

      and they used to carry a "aircraft grade" steel one with a smaller flange on it that worked...
    17. Thread: Air Ride Help!

      by zrau17
      Replies
      28
      Views
      1,205

      Grind the actual hole out more. Meaning, make the...

      Grind the actual hole out more. Meaning, make the diameter of it larger. Don't shorten the lip. You're not destroying your car. Just get a dremel or something with a high grit sanding thing on it...
    18. Thread: I'm bored.

      by zrau17
      Replies
      13
      Views
      607

      I'm bored.

      Seems like this place is getting flooded with dumber **** every day, dumb cars.

      Can't imagine it's gonna stay like this much longer, getting old. Was nice to meet a few of you at h2o, I apologize...
    19. Replies
      33
      Views
      2,281

      When I had this manifold, my solution was brand...

      When I had this manifold, my solution was brand new stainless studs with brand new stainless flanged 10mm head nuts and nordlocks. Made life easy the next time around. I was always able to get a 10mm...
    20. Thread: Air Ride Help!

      by zrau17
      Replies
      28
      Views
      1,205

      Do NOT do that. Completely wrong. You're supposed...

      Do NOT do that. Completely wrong. You're supposed to open up the hole a little bit so the plastic bag bracket sits all the way down and rests on the spring mount. If you cut it off it will slide and...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4