Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: AFRich337

    Page 1 of 13 1 2 3 4

    Search: Search took 0.80 seconds.

    1. Replies
      29
      Views
      1,847

      I'm very curious now, and I really want to know....

      I'm very curious now, and I really want to know.

      I know this GTI won't be in any events that require it to conform to FIA regulation, but this information is interesting and may be relevant. It...
    2. Replies
      29
      Views
      1,847

      What about Lululemons? Thanks! I...

      What about Lululemons?



      Thanks!



      I appreciate the concern for a complete stranger over the internet. :thumbup:
    3. Replies
      29
      Views
      1,847

      I've been told that and varying degrees of angle...

      I've been told that and varying degrees of angle that are supposedly correct and incorrect. I don't know who to believe and where anybody gets their information from.

      I figure an accident on a...
    4. Replies
      29
      Views
      1,847

      I used a razor blade at a shallow angle as to not...

      I used a razor blade at a shallow angle as to not risk scratching the glass. Once I get ahold of a lifted piece of tint, I just start carefully pulling it off. It helps to have the car parked out in...
    5. Replies
      29
      Views
      1,847

      I honestly didn't intend to imply that I was...

      I honestly didn't intend to imply that I was having a condescending or sarcastic attitude. I sincerely and genuinely do want to know why the rear seat belt anchor points should not be used because...
    6. Replies
      29
      Views
      1,847

      I'd like to know why you think the Schroth...

      I'd like to know why you think the Schroth harnesses shouldn't be installed into the points as instructed. To me, it makes sense to reuse the rear seat belt anchor points since they are used by the...
    7. Replies
      6
      Views
      359

      I'm in West San Jose. PM me and we can get...

      I'm in West San Jose. PM me and we can get something set up for getting your fenders rolled.
    8. Adjusting idle torque/speed. Lightened flywheel.

      I have a 20 pound, single-mass flywheel with my AWP 1.8T in a 2002 GTI. At idle with the clutch out in neutral, it chatters from the gear lash. Currently, my idle speed is untouched and is at...
    9. WTB: Early Mk1 Audi TT control arms w/ nubs

      I'm looking for a set of the early Mk1 Audi TT control arms with the nubs in front. I will be installing TT/R32 spindles, and I need the nubs so I can drill and tap them so I can still use my current...
    10. Replies
      12
      Views
      500

      :thumbup:

      :thumbup:
    11. Replies
      48
      Views
      2,036

      Please un-black everything. Poor people mods......

      Please un-black everything. Poor people mods... Ugh. What's more disgusting?
    12. Replies
      28
      Views
      4,497

      Stupid question gets totally irrelevant but...

      Stupid question gets totally irrelevant but awesome pics and gifs. MkIV forum has gone down the pooper, except for dem gurlz doe.
    13. I needed this DIY, and the instructions and...

      I needed this DIY, and the instructions and photos are clear and concise. Good job!
    14. FS: Mk4 R32/Mk1 TT (revised) Control Arms

      SOLD

      I have a set of used Mk4 R32/Revised Mk1 Audi TT control arms for sale. They have 77k miles on them with the original bushings. Since they are the revised control arms, these do not have the...
    15. I wanted to use the R32 control arms for the...

      I wanted to use the R32 control arms for the ability to adjust for a bit of negative camber, but I have a friend who will sell me his old TT arms that have the nubs to be drilled and tapped for the...
    16. I forgot to mention they are R32 spindles. I...

      I forgot to mention they are R32 spindles. I agree that it's best to replace the bearings while the hubs are still good and the spindles are already out.

      I was thinking that they would probably...
    17. Play in front wheel hub in spindle but not installed on car

      I just got some used spindles with 77k miles on them, and they have the proper 6-speed hubs. There is a bit of play when I wiggle the hubs. Is this normal when the spindles are not installed on the...
    18. Before you replace your faulty window switch, read this

      I haven't seen any DIYs on how to fix the problem of window switches that stop working, so I just took apart mine last night to take a look at the insides. I didn't want to spend the $50-$99 on a...
    19. Replies
      4
      Views
      810

      I'd skip the front sway bar and only get a rear...

      I'd skip the front sway bar and only get a rear bar. It'll be most effective and best for handling for our cars. With just the rear bar, you'll feel less body roll as well.

      There are benefits to...
    20. Replies
      4
      Views
      1,347

      If you remove the helper spring, you would have...

      If you remove the helper spring, you would have to preload the main spring with the height adjustment rings. Since you will be setting the height adjustment lower to preload the spring, and you don't...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4