Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: need_a_VR6

    Page 1 of 13 1 2 3 4

    Search: Search took 0.37 seconds.

    1. Thread: DELDUBS

      by need_a_VR6
      Replies
      46,037
      Views
      1,422,287

      24v GLI or 1.8t GLI? Either way, no.

      24v GLI or 1.8t GLI? Either way, no.
    2. Replies
      3
      Views
      166

      Just the two wires for the idle valve or cut...

      Just the two wires for the idle valve or cut power.
    3. Replies
      3
      Views
      166

      Try completely unplugging the idle portion. It...

      Try completely unplugging the idle portion. It should idle ~900 rpm that way. If not check for vacuum leaks.
    4. Replies
      75
      Views
      7,774

      2376 is pretty light. Mine was 2550 at the...

      2376 is pretty light. Mine was 2550 at the lightest I ran it.

      103mph should get you close to 13.40

      I like the 225/50 bfgs the best out of all the appropriate sized drag radials.
    5. Replies
      16
      Views
      997

      I could.

      I could.
    6. Replies
      16
      Views
      997

      I could easily take a picture of both...

      I could easily take a picture of both headgaskets. Thats why.
    7. Replies
      1,346
      Views
      125,047

      I broke a 3rd gear na. Unless I see straight cut...

      I broke a 3rd gear na. Unless I see straight cut dog gears in there, well, good luck.
    8. Replies
      16
      Views
      997

      Nater often wonders why I collect headgaskets.

      Nater often wonders why I collect headgaskets.
    9. Replies
      127
      Views
      38,747

      You can hear the big motor for a few seconds at...

      You can hear the big motor for a few seconds at least.

      You will get it sorted soon.
    10. The OBD2 tb requires an actual servo driver to...

      The OBD2 tb requires an actual servo driver to make it work right. You can "kind of" make it work with MS with the right wiring and the right duty, but not exactly like factory. With NO wiring it...
    11. Replies
      11
      Views
      551

      That dark area is above where the top ring sits,...

      That dark area is above where the top ring sits, which is why it's darker. It never gets scraped by the rings.

      That being said without measuring the bore, it's a total crap shoot.
    12. Try pushing on u9 to see if there is an...

      Try pushing on u9 to see if there is an intermittent connection. Theres not much to go bad other than that or the max232 chip.
    13. If you dont want to open the case check for 5v...

      If you dont want to open the case
      check for 5v on tps vref when it goes out. I have seen shorts overload the polyfuse that are intermittent like that.
    14. I had a similar issue on one ecu. Seemed hardware...

      I had a similar issue on one ecu. Seemed hardware related but couldn't find anything wrong. Reflashed with debug level 3 (serial comms) and it worked fine after. I would give that a shot and report...
    15. Replies
      11
      Views
      551

      On everything but a fresh machined block.

      On everything but a fresh machined block.
    16. I have a diy in the 12v forum that covers it...

      I have a diy in the 12v forum that covers it generally.
    17. Porting only. Remove the casting flash and smooth...

      Porting only. Remove the casting flash and smooth transitions. Match outlet to inlet of the downpipe. Took me about four hours for the pair. Usually an hour or two more for 12v ones as they need more...
    18. Replies
      2
      Views
      165

      Just make sure its from the same setup (obd1,...

      Just make sure its from the same setup (obd1, coilpack, 4pin maf and auto or manual)
    19. Replies
      11
      Views
      551

      Check the bore and ring gap at top/middle/bottom....

      Check the bore and ring gap at top/middle/bottom. Set gap at tightest part and cross your fingers.

      Usually oil consumption isnt the comp ring. I would inspect for a cracked oil ring, happens a...
    20. There is a lot of work you can do to them still....

      There is a lot of work you can do to them still. The inlet is a lot better, but thats about it.
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4