Search Results - Vortex Media Group
Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: PencilGeek

    Page 1 of 3 1 2 3

    Search: Search took 0.14 seconds.

    1. Replies
      141
      Views
      64,611

      Here's another dyno chart with smoothing enabled....

      Here's another dyno chart with smoothing enabled.

      http://www.rcollins-home.org/photobucket/albums/Car_Porn/2015-05-14_Drake_16V-VW_Build/50_Drake%2016v%20Dyno/Poly-Dyno.jpg
    2. Replies
      141
      Views
      64,611

      I do. I have video of the dyno, but it's not...

      I do. I have video of the dyno, but it's not edited. Give me a few days and I'll upload something to youtube.
    3. Replies
      141
      Views
      64,611

      Engine: 1982 cc's Compression: 9.5:1 Cylinder...

      Engine: 1982 cc's
      Compression: 9.5:1
      Cylinder head: Drake Engineering 16v
      Induction: Dual Weber 45 DCOE
      Gasoline: 100 octane
      Spark: MSD-6A Ignition

      Horsepower: 211 hp @ 7300 RPMs
      Torque: 164...
    4. Replies
      141
      Views
      64,611

      I didn't realize I dropped the ball and didn't...

      I didn't realize I dropped the ball and didn't post any graphs or photos. I'll see if I can post a few photos and the dyno graphs over the next few days.
    5. Replies
      2
      Views
      469

      It sounds like you already know this, but just to...

      It sounds like you already know this, but just to be sure...

      Compression ratio can't be measured by things like cylinder pressure, it must be calculated from measurements like cylinder volume. As...
    6. Replies
      141
      Views
      64,611

      Yes it is an engine dyno, no drivetrain loss. ...

      Yes it is an engine dyno, no drivetrain loss. Water pump = yes, power steering = no, alternator = yes. The engine is configured exactly like it will go in the car.

      I'm working to start a build...
    7. Replies
      141
      Views
      64,611

      Of course it's possible. But adding advanced...

      Of course it's possible. But adding advanced electronics and an ECU was not what this owner wanted. The owner wanted the engine to be built for the same era as the car that will receive it. It...
    8. Replies
      141
      Views
      64,611

      This is an old school motor without knock sensor...

      This is an old school motor without knock sensor and set to run on pump gasoline. I believe 9.5:1 is as high as you'd want to go.
    9. Replies
      141
      Views
      64,611

      Here's a bit of a teaser. I'll try to get many...

      Here's a bit of a teaser. I'll try to get many more details posted in the next few days.

      Engine: 1982 cc's
      Compression: 9.5:1
      Cylinder head: Drake Engineering 16v
      Induction: Dual Weber 45...
    10. Replies
      141
      Views
      64,611

      The Drake 16V started on the dyno Friday. But...

      The Drake 16V started on the dyno Friday. But now she takes about 10 days off while Van Dyne goes to Indy for the 500. Dyno will resume in about two weeks. I'm hoping we'll get video and sound...
    11. Replies
      141
      Views
      64,611

      The engine made its way to the dyno yesterday. ...

      The engine made its way to the dyno yesterday. It is being strapped down and will run over the next few days. But the Indy-500 comes right in the middle of this, and Van Dyne leaves for Indy Sunday...
    12. Replies
      141
      Views
      64,611

      There's five or six heads available without...

      There's five or six heads available without producing any new ones. Give Van Dyne a call if interested.
    13. Replies
      141
      Views
      64,611

      Here's an update. The carb manifolds are done...

      Here's an update.

      The carb manifolds are done and installed. The throttle linkage was designed, manufactured and installed. The carbs were brand new Weber DCOE "old new stock" -- meaning they...
    14. Replies
      141
      Views
      64,611

      Last I checked, the intake manifolds had been...

      Last I checked, the intake manifolds had been anodized and ready to assemble. The carbs we had originally chosen were going to need a complete rebuild since they sat around for such a long time. If...
    15. Replies
      141
      Views
      64,611

      I realize it's been a long time, but I can assure...

      I realize it's been a long time, but I can assure you it hasn't fallen off the rails. Instead of going back through the thread to reacquaint myself with my own last status, I'll just give a status...
    16. Replies
      141
      Views
      64,611

      Since no original intake manifolds were still...

      Since no original intake manifolds were still available, new ones had to be cast from the original molds. That took a lot longer than expected. But they are now cast, machined, and ready to use.
      ...
    17. Replies
      141
      Views
      64,611

      Yes, there's still 4 or 5 heads available for...

      Yes, there's still 4 or 5 heads available for purchase. If Stewart runs out, then he owns all of the molds and CNC programming to make new ones.

      Even though any purchase would have to be...
    18. Replies
      141
      Views
      64,611

      PM sent.

      PM sent.
    19. Replies
      141
      Views
      64,611

      Yes. And progress continues to be made on the...

      Yes.

      And progress continues to be made on the build.
    20. Replies
      141
      Views
      64,611

      The bottom end is complete. Crank, rods, pistons...

      The bottom end is complete. Crank, rods, pistons installed. Block painted, oil pump installed, oil pan installed. Next task: assemble and install the Drake 16v head. We're shooting for early...
    Results 1 to 20 of 54
    Page 1 of 3 1 2 3