Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: J. Daniel

    Page 1 of 13 1 2 3 4

    Search: Search took 0.56 seconds.

    1. Replies
      47
      Views
      4,582

      I noticed you installed a 16V rear axle complete...

      I noticed you installed a 16V rear axle complete with anti-sway bar, but I don't see a front bar.
      I believe your handling is going to be badly unbalanced without a front bar. It's going to be really...
    2. Replies
      10
      Views
      565

      With a turbo a stock 16V clutch isn't going to...

      With a turbo a stock 16V clutch isn't going to cut it.
      I have a 2.0 turbo and was told a Sachs sport clutch would be a good street clutch for it. It wasn't! It slipped easily.

      Spec stage 3 in my...
    3. Replies
      31
      Views
      920

      2.0 ABA, TT 8V ported head and intake manifold,...

      2.0 ABA, TT 8V ported head and intake manifold, TT 2.25 exhaust and downpipe w/4 into 2 ported exhaust manifold, 274 cam, Haltech...
    4. What's going on here? The weather is warming up,...

      What's going on here?
      The weather is warming up, work has to be getting done, and this thread has dropped to the second page?
      What's up, what's up, what's up?????:D
    5. They went from two progressive plates of...

      They went from two progressive plates of approximately the same area to one plate. An obvious cost savings deleting one plate, shaft, screws and associated linkage for no performance loss. They just...
    6. I call BS. It may seem so but the butt dyno...

      I call BS. It may seem so but the butt dyno responds to change in acceleration not acceleration itself. The single plate throttle body dumps a load of air in with minimal opening so the change in...
    7. Replies
      8
      Views
      610

      The method I used took 4 strut housings to make...

      The method I used took 4 strut housings to make 2. Not efficient.
      Team Andy had a different approach and just modified 2 housings. I don't know of any thread on their modification but I know for...
    8. Replies
      5
      Views
      472

      15 from vertical relative to the top of the...

      15 from vertical relative to the top of the block. :)
    9. Replies
      8
      Views
      610

      Depending on how low your car is the impact...

      Depending on how low your car is the impact harshness may be the suspension bottoming out. There isn't much compression travel on the front struts even when moderately lowered.
      The "fix" as far as I...
    10. bump for the Bilstiein front shocks and sunroof...

      bump for the Bilstiein front shocks and sunroof seal.
    11. Sorry, that is sold.

      Sorry, that is sold.
    12. Bump

      Bump
    13. Replies
      33
      Views
      1,104

      Cathy, dammit, I didn't mean it that way. I meant...

      Cathy, dammit, I didn't mean it that way. I meant the OP was the genius! You have to catch that famous J. Daniel sarcastic attitude. :laugh:
    14. Replies
      20
      Views
      1,060

      Thanks! Quite frankly if I had it to do over...

      Thanks!
      Quite frankly if I had it to do over again I'd go 15 X 7. Or maybe 15 X 8 if I could find them. :P
      I don't want to drop the car too far on the suspension, but a little lower overall would...
    15. Floor mat pics for those interested

      Nothing to see here. They are sold.
    16. Replies
      33
      Views
      1,104

      Amazing how there are 25 idiots and one genius in...

      Amazing how there are 25 idiots and one genius in this thread!:rolleyes:
    17. Replies
      20
      Views
      1,060

      I've run 7 X 16 BBS ET 35 rims for years with no...

      I've run 7 X 16 BBS ET 35 rims for years with no rubbing. 205/40 tires and 205/45 tires. But I'm not running insanely low either.
      The back can use spacers to bring the wheels out a little, but...
    18. Replies
      33
      Views
      1,104

      Cute! Scolding the other posters when you're in...

      Cute! Scolding the other posters when you're in the wrong forum and your post is so obscure nobody knows what the feck you're talking about.:laugh:
    19. Bumpedy, bump, bump

      Bumpedy, bump, bump
    20. Replies
      5
      Views
      580

      I'm going to guess from the markings that the cam...

      I'm going to guess from the markings that the cam has .426 lift and 110 lobe centers. No clue what the "1" and "400" might represent.

      In my experience if the cams are accurately ground with...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4