Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: graeme86

    Page 1 of 13 1 2 3 4

    Search: Search took 0.63 seconds.

    1. Replies
      6
      Views
      252

      Look here too: ...

      Look here too:

      http://forums.vwvortex.com/showthread.php?7172629-Interior-shifter-play

      The rest of the shifter may need a bit of a refresh if the bushes are worn.

      That Dieselgeek First Gear...
    2. Replies
      6
      Views
      252

      Can you get someone to hold the shifter inside in...

      Can you get someone to hold the shifter inside in the neutral plane and push it as far over to the left as it will go without depressing the lever.

      Or in case of B & M not pulling it up. :P
      ...
    3. Replies
      39
      Views
      1,821

      :laugh:

      :laugh:
    4. Replies
      39
      Views
      1,821

      Check these bolts for free first. ...

      Check these bolts for free first.

      http://www.users.on.net/~graeme86/camsensor/camsensors.jpg

      They come loose and car gets sluggish as well with no codes - fairly common issue.
      ...
    5. Study this carefully. R32 Fan Schematic...

      Study this carefully.

      R32 Fan Schematic

      Some points of the R32 system:

      The FCM runs the timer for the afterrun water pump.

      The FCM interprets the Duty Cycle signal from the AC Pressure...
    6. Clear any fault codes in -17- and -19- Recode...

      Clear any fault codes in -17- and -19-

      Recode the CAN gateway -19- again with same code, even if it is correct now.

      That will re-establish the CAN network.

      That will fix the error you are...
    7. Replies
      1,110
      Views
      222,675

      Australian market authorised accessories...

      Australian market authorised accessories sold/fitted at the dealer are listed in a printed catalogue, they are not listed in etka.

      It's not even a properly printed catalogue, it's a printed page...
    8. Replies
      1,110
      Views
      222,675

      The only ones I have information for are the...

      The only ones I have information for are the Australian part number VWA0029 with two pinstripes and VW emblem.
    9. Replies
      2
      Views
      195

      The CCM should just plug in. You may just have to...

      The CCM should just plug in. You may just have to re-sync the remotes as per the owners manual.

      You may need vagcom to do your adaptions again, like one touch, auto closing etc if the new CCM was...
    10. Replies
      18
      Views
      1,353

      You can only get to that cable end by coming in...

      You can only get to that cable end by coming in from underneath and removing the bottom cover #28
    11. Replies
      5
      Views
      270

      The M10x1 is the bottom drain plug. The M14x1...

      The M10x1 is the bottom drain plug.

      The M14x1 is the one on the side of item #1

      :)
    12. Replies
      27
      Views
      1,138

      The stock arms are slightly slotted where ther...

      The stock arms are slightly slotted where ther outer bolt goes, so there is a very small adjustment available.

      http://www.users.on.net/~graeme86/suspension/longarm.jpg

      You can also adjust the...
    13. Replies
      1,110
      Views
      222,675

      The ones for sale in UK are a different part...

      The ones for sale in UK are a different part number to the Australian dealer ones, even though they are both made here.:screwy:

      The UK versions don't have the VW emblem on them as far as I am...
    14. Follow the normal "DRL disabling" instructions. ...

      Follow the normal "DRL disabling" instructions.

      Tape up/bend Pin 3 or remove the harness wire from that pin and insulate.

      I believe if you fully remove the US DRL relay, then the handbrake...
    15. You are somehow connected to the DRL circuit,...

      You are somehow connected to the DRL circuit, which only comes on when handbrake is released (due to way the US DRL relay is wired)

      Euro switch outputs 12V to "TFL" pin 3 in -0- position with...
    16. Replies
      1,110
      Views
      222,675

      Local dealer in Australia still sells brand new...

      Local dealer in Australia still sells brand new Jetta covers. ;)

      PM if interested

      :)
    17. Replies
      12,211
      Views
      986,155

      Received this in the mail today Hazet 2169-36...

      Received this in the mail today

      Hazet 2169-36 Oil Filter tool

      http://www.users.on.net/~graeme86/misc/hazet2169-36_1.jpg

      http://www.users.on.net/~graeme86/misc/hazet2169-36_2.jpg

      Bought it...
    18. Replies
      17
      Views
      1,628

      Great information :thumbup: I was thinking...

      Great information :thumbup:

      I was thinking perhaps you could also use a Mk V SAI pump bracket 022 131 085 H like this:
      ...
    19. Replies
      169
      Views
      47,363

      The module needs to be coded according to ELSA....

      The module needs to be coded according to ELSA. Supposedly the coding can be done with "guided functions" by the dealer.

      The only thing I have found on Brasil forums is a copy of a page with the...
    20. Replies
      7
      Views
      242

      Thanks for the head's up...best not to tap that...

      Thanks for the head's up...best not to tap that plate then. :D
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4