Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: Budsdubbin

    Page 1 of 13 1 2 3 4

    Search: Search took 0.73 seconds.

    1. That info isn't anything new. In your case...

      That info isn't anything new. In your case sticking with power enrichment is the way to go. I've always used it. Also you won't be able to correct for 30psi because of the map limit. Stick with your...
    2. power enrichment uses throttle input(value isn't...

      power enrichment uses throttle input(value isn't TPS but torque request from throttle map), full load uses calculated load for target lambda. You can use either map but if your using full load lambda...
    3. your seeing 20-25 degrees because your only...

      your seeing 20-25 degrees because your only hitting around 160% load. You either need to correct your load calculation or soften the timing map in those load area's, fixing the load calculation would...
    4. Just weld up the joints and buy vband kits, cut...

      Just weld up the joints and buy vband kits, cut and weld you'll have a exhaust that works well. I've experienced too many of those joints just being complete nightmares even using band clamps. In the...
    5. :thumbup: spot on

      :thumbup: spot on
    6. Only in higher level emissions regulated states...

      Only in higher level emissions regulated states such as NJ/NYC/california. I think its just for the monitors that show up as "N/A" or not installed. Which is easier to do than forced readiness. If...
    7. Readiness can be forced in the tune if the tuner...

      Readiness can be forced in the tune if the tuner has the knowledge to do so without emissions plugged in but Evap solenoid should be plugged in or resistored.
    8. Replies
      11
      Views
      623

      I've used it to flash and pull binary works fine...

      I've used it to flash and pull binary works fine on me7.X ecu's :confused:
    9. :thumbup:

      :thumbup:
    10. you can change the TPS axis to whatever you want...

      you can change the TPS axis to whatever you want but just make sure your changes to that axis are reflected in the inverse throttle vrs air map or else its gonna run horribly. You can either use your...
    11. Replies
      37
      Views
      1,780

      :thumbup::beer:

      :thumbup::beer:
    12. stock PCV is very well throught out. It works in...

      stock PCV is very well throught out. It works in two stages:

      1.) Puck on the intake is utilized pulling pressure from crankcase while in boost
      2.) PCV in the shape of a Y around the intake pulls...
    13. Replies
      17
      Views
      887

      Sunday or Tuesday I'm down

      Sunday or Tuesday I'm down
    14. Replies
      17
      Views
      887

      Unless the inspector went in there and manuelly...

      Unless the inspector went in there and manuelly input n/a during the visiual check list.
    15. Replies
      17
      Views
      887

      I have n75, rear o2 and n80 for evap plugged in....

      I have n75, rear o2 and n80 for evap plugged in. I've passed western New York's emissions since 2007. And it's not like you have advanced emissions like NYC, nj or California so something's up.
    16. Replies
      17
      Views
      887

      Turn engine misfire diagnosis on. If you switch...

      Turn engine misfire diagnosis on. If you switch "off" on Maestro for egr flow, rear o2 should be left in but turn off diag., secondary air off , evap. Off but solenoid plugged in all should report...
    17. I thought there was something a bit funky with...

      I thought there was something a bit funky with the bvc he gave me. Thanks for posting them!
    18. Those values are different from what I've got...

      Those values are different from what I've got from Q?

      @43.5psi
      8v 10 12 14 16

      2.5ms 1.6 1.25 .97 .97
    19. Coolant ball delete: aftermarket expansion tank ideas/options

      So I'm looking for feedback on expansion tank options. I keep running into issues with banjo gaskets leaking after WOT pulls and overheating issues in traffic. I have an issue with high speed cooling...
    20. I can say that I have a similar case. Low speed...

      I can say that I have a similar case. Low speed fans work when jumped from 1 to 2, but high speed will not jump. A/C is evacuated, a/c high pressure switch is removed (pigtail open). I believe it may...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4