Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: 81golfcaddy

    Page 1 of 13 1 2 3 4

    Search: Search took 0.48 seconds.

    1. Replies
      1
      Views
      298

      Never mind my bad 2.0 aba is 11 mm

      Never mind my bad 2.0 aba is 11 mm
    2. Replies
      1
      Views
      298

      1.6 12 mm head studs from aba.

      I have a set of head studs from a 2.0 aba engine. Both are 8v both are 12mm. Will the head studs work on the 1.6 Diesel engine.
    3. doubt that is the problem but a new set of plugs...

      doubt that is the problem but a new set of plugs cant hurt. after this new ecu will be on the way if not that then I will switch over to OBD2. thanks for input
    4. The thing that gets me is it will run so good...

      The thing that gets me is it will run so good until it starts warming up and the the smoke starts to appear then idle gets lumpy then the same plug will foul each time.
    5. Ngkbkr7e

      Ngkbkr7e
    6. I converted to ce2 checked all grounds...

      I converted to ce2 checked all grounds connections yesterday and all looked good. 02 is new. Something I did notice strange #2 injector will be the first to foul out each time. Had a extra set of...
    7. OBD1 vr burning extremely rich when engine warms up

      hello I have a 87 jetta with vr swap running on motronic obd1. engine has been bored out schrick cams head ported and headers. (software is stock as of now) engine fires up and runs smooth then...
    8. 81 caddy diesel overheating at random times

      hello my 81 diesel has this weird overheating issue. at random time the temp will start climbing very fast and heat will stop working and bottom radiator hose will be cold. I can crack the lid on...
    9. Replies
      9
      Views
      1,003

      sorry to abandon the thread. the car is my daily...

      sorry to abandon the thread. the car is my daily driver now about 100 miles each day. the only issue I am having now is I believe it has a bad ecu. it will go lean sometimes under boost when it feels...
    10. Replies
      12
      Views
      1,071

      not sure about the thickness of spacer since...

      not sure about the thickness of spacer since engine was together when i got it. it looks pretty thick like 1/4 inch thick. as far as the soft ware it is written on top of the ecu with a marker c2...
    11. Replies
      10
      Views
      2,987

      http://i30.photobucket.com/albums/c327/81golfcaddy...

      http://i30.photobucket.com/albums/c327/81golfcaddy/Mobile%20Uploads/image_zpsc63a5bd5.jpg[/URL]
    12. Replies
      10
      Views
      2,987

      Feeler 84 Rabbit daily driver vr6 turbo

      Just looking to see what may be out there. This is my 84 Rabbit vr6 turbo C2motorsports stage 1. Engine has head spacer arp studs short runner intake ATP turbo and manifold Tial waste gate forge...
    13. Replies
      12
      Views
      1,071

      I can check again but I have replaced both ecu...

      I can check again but I have replaced both ecu harneses with same results. moving the sensor to the fuel rail to fool the ecu stops this problem. the engine runs great not ticking or knocking or for...
    14. Replies
      12
      Views
      1,071

      tried the rubber washers behind the knock sensor...

      tried the rubber washers behind the knock sensor and it did the trick for #1 but did nothing for #2 at front of engine. I was monitoring them while driving and they were close until I started to get...
    15. Replies
      12
      Views
      1,071

      The plugs are new and I have monitored the knock...

      The plugs are new and I have monitored the knock voltage and it increases with rpms above 2500 and will start pulling timing shortly after 3k with no load at all on engine. like I said before you can...
    16. Replies
      12
      Views
      1,071

      you are correct about the front one I have had it...

      you are correct about the front one I have had it off several times with no luck. I did try the plastic/neoprene oil plug washers with no luck. what thickness rubber are we talking about here and I...
    17. Replies
      12
      Views
      1,071

      I actually tried the washers and spacers with no...

      I actually tried the washers and spacers with no difference. you can slowly reve the engine up in netural and you start to feel a vibration near 2500 rpm. it has heavy duty engine mounts not sure if...
    18. Replies
      12
      Views
      1,071

      No one ?

      No one ?
    19. Replies
      12
      Views
      1,071

      Vr6t knock sensor signal too high

      This is a 84 rabbit with a 2000 model vr6t on motronic c2 stage 1 with head spacer short runner and inter cooler
      This is a list of parts that have been replaced. Both knock sensors ( correct torque...
    20. Replies
      4
      Views
      752

      will run separate ground from battery to ECU in...

      will run separate ground from battery to ECU in the morning and see if there is any change. if not will try new ECU. I can pick one up for about 75.00 and a local tuner will load my software and...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4