Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: AL@PagParts.com

    Page 1 of 13 1 2 3 4

    Search: Search took 0.50 seconds.

    1. Replies
      10
      Views
      438

      I'd probably stop at 400whp. It can tolerate more...

      I'd probably stop at 400whp. It can tolerate more when everything is working but the cast pistons do not absorb mistakes (boost/fueling anomalies) very well. We've cracked ring lands (prob due to...
    2. Not sure how to answer that question as its just...

      Not sure how to answer that question as its just a piece that has a lot of shortcomings. Try to port and open up the collector area alot. Not much you can do about the cavity that is around the wg...
    3. Well, if you look at the manifold, its got some...

      Well, if you look at the manifold, its got some funky tight bends past the ports then triangulates abruptly into somewhat of a collector/wastegate area then you have an equally abrupt turn into the...
    4. Didnt mean to throw chickenman under the bus at...

      Didnt mean to throw chickenman under the bus at all but these were my observations on two cars that I had finished up that came in to our shop. On both cars, there was a definite excessively heated...
    5. I actually have first hand experience with that...

      I actually have first hand experience with that manifold. It is major backpressure issues where you can visible see the hpc coating burn off right by the collector. The car that it was installed on...
    6. Yes, before you fry your exhaust guides/valves...

      Yes, before you fry your exhaust guides/valves...
    7. If you are running 630's on an aeb file and are...

      If you are running 630's on an aeb file and are concerned about your idle, its not necessarily your injectors at all. AEB's need to be properly set up and are even more sensitive to leaks then the...
    8. New lifters with new cams period

      New lifters with new cams period
    9. Cat 3658s are more then fine. I have a small...

      Cat 3658s are more then fine. I have a small batch coming in if you'd like to reserve a set
    10. There is no real need for the billet ones. The...

      There is no real need for the billet ones. The new cast renditions can be had with oem - like pressed gears with marks which are more budget friendly and hassle free
    11. I can actually modify your existing 3071r (if in...

      I can actually modify your existing 3071r (if in good condition) to the 35R frame. If its a bit tired or you want to start from new, we can send her in for the bearing program and then modify after.
    12. Replies
      151
      Views
      28,757

      Pete, there needs to be a bit of room for turbos...

      Pete, there needs to be a bit of room for turbos to ramp up to peak boost. There's not enough flow to ramp up the turbine to 170k+ shaft speeds at 3k on this motor. Not saying your tests arent valid...
    13. Replies
      151
      Views
      28,757

      Found another interesting one... Same STI...

      Found another interesting one...

      Same STI swapped from single to twin scroll
      http://i.imgur.com/KFrRuW8.jpg

      QUOTE:
      "This car is an SCCA Solo car so the owner was looking for more down low and...
    14. Replies
      202
      Views
      15,823

      Yes, lynch mob status :). Even if you punch in...

      Yes, lynch mob status :). Even if you punch in one of the numbers he provided, you will most likely get the hydro pulley. I dont think there's tons of these individual components floating around and...
    15. Replies
      202
      Views
      15,823

      It would be misleading to give a part number for...

      It would be misleading to give a part number for a part that comes in 2 versions. The hydro setup uses the same kit part number without the hydro tensioner. I throw a part number out there and you...
    16. Replies
      202
      Views
      15,823

      Before you insinuate that I was hoarding...

      Before you insinuate that I was hoarding information, I'll have you know that I ran into this kit by mistake. Yes, the KIT. I have to purchase the entire kit just like everybody else. I didnt splash...
    17. Replies
      151
      Views
      28,757

      This is a boost graph (green) of a 7670 on an EVO...

      This is a boost graph (green) of a 7670 on an EVO 2.3L with twin scroll housing. Only one I can find on an actual vehicle... I notice the internal gate losing a bit of steam upstairs as most of them...
    18. Replies
      202
      Views
      15,823

      So far as I can tell, you cannot purchase these...

      So far as I can tell, you cannot purchase these components separately. I've searched...
    19. Replies
      62
      Views
      20,180

      I will get that going as soon as I can. The TS...

      I will get that going as soon as I can. The TS would be nice and I may get to that at some point but they do present more of a challenge in packaging. If they are anywhere near the 6758's, I think it...
    20. Replies
      151
      Views
      28,757

      There is a 3rd gear spool chart on the previous...

      There is a 3rd gear spool chart on the previous page. Mind you, this is on the FSI motor so its going to be slightly different. 20psi by around 3600rpm's in 3rd. I see 15psi in 2nd gear around the...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4