Search Results - Vortex Media Group
Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: acee_dub

    Page 1 of 13 1 2 3 4

    Search: Search took 0.19 seconds.

    1. Replies
      7
      Views
      721

      Cool, thanks everyone for the input, very helpful...

      Cool, thanks everyone for the input, very helpful :beer:
    2. Replies
      4
      Views
      700

      Look into diesel truck, excavator or bus turbos.....

      Look into diesel truck, excavator or bus turbos.. many common vehicles came with holset turbos and you can probably source one from a scrapper or buy one online.. check out this thread for more...
    3. Replies
      7
      Views
      721

      This EBC, boost control works fine at lower...

      This EBC, boost control works fine at lower levels, raising by 10% from 0 - 100 duty cycle it slowly raised boost, and held steady at the mark.. in higher boost levels gets weird.. (at 100% duty only...
    4. Replies
      7
      Views
      721

      Maximum Boost? VRT

      I have a 12v VR6 on standalone (ms2 v3) I have maxed out the electronic boost controller settings in attempt to hit my 2BAR goal, however it would only peak at 1.2BAR, and lower off to 0.9BAR past...
    5. Replies
      7
      Views
      1,263

      Who makes this prefab stainless 3" exhaust you're...

      Who makes this prefab stainless 3" exhaust you're talking about? I have an mk3 vrt and need DP-Back 3" also located in ontario.. I don't think you can use mk3 exhaust on an mk2 though. But am not 100%
    6. Thread: bov rattle?

      by acee_dub
      Replies
      1
      Views
      366

      Can you post a youtube video with the sound you...

      Can you post a youtube video with the sound you are describing?
    7. Replies
      2
      Views
      520

      Look into Holsets,...

      Look into Holsets, http://forums.vwvortex.com/showthread.php?4894145-Holset-user-thread
    8. Replies
      3
      Views
      727

      If you are aiming for the best possible response,...

      If you are aiming for the best possible response, I would get the twin scroll housing, and pair it with a twin scroll manifold.. or maybe a quick spool flapper valve.
    9. Must be that rust colour spray job.. I'll get...

      Must be that rust colour spray job.. I'll get someone to rev it tomorrow and see where it's coming from, would be wicked if it isn't the pan, but I see the right side of it is really wet
    10. You mean these? http://i.imgur.com/BQFoFxZ.jpg...

      You mean these?

      http://i.imgur.com/BQFoFxZ.jpg

      http://i.imgur.com/sjy5KqU.jpg
    11. Oil Pan Leaking (Torqued proper + RTV on new gasket)

      I have reinstalled my oilpan with a new gasket, put Permatex Ultra Black on both sides of it and torqued to spec as per bentley, and it is still leaking. Could my bolts be stretched out or should I...
    12. Replies
      8
      Views
      1,251

      Solved! The problem was that the ignition...

      Solved!

      The problem was that the ignition input capture should have been set to Falling Edge.

      This can be tested for using a tooth logger

      Bad (2 long):
      http://puu.sh/isGxH/3299178402.png...
    13. Replies
      8
      Views
      1,251

      It seems the desync only occurs between 1100-1300...

      It seems the desync only occurs between 1100-1300 rpms, and if i keep it within that range, it will keep desyncing over and over

      -not noise
      -not dirty sensor
      -not tpsvref voltage

      Tried...
    14. Replies
      8
      Views
      1,251

      I removed and cleaned the sensor, reinstalled and...

      I removed and cleaned the sensor, reinstalled and retested to no avail.. Checked pin 26 of megasquirt with a multimeter when running and it was getting 4.86v, this value did not change when desyncing...
    15. Replies
      8
      Views
      1,251

      http://puu.sh/ihusl/9fd054c9c5.png ...

      http://puu.sh/ihusl/9fd054c9c5.png

      http://puu.sh/ihuKv/596e9380ac.png

      http://puu.sh/ihuQM/161d52167f.png

      http://puu.sh/ihv0l/4b59d309de.png

      The trigger log showed desync every time this...
    16. x2 Check for spark / fuel, getting a datalog of...

      x2 Check for spark / fuel, getting a datalog of it cranking helps see whats going on, if you post it up here it helps us to watch the replay of it through megalogviewer (you can make a log through...
    17. Replies
      8
      Views
      1,251

      SOLVED MS2 v3.0 on 12v VRT (Desyncing @ 1000~ rpm)

      Hi, I just got my VRT running on MS2v3 and have been getting fluctuating RPM / Leaning out when adding throttle gradually from idle (occurs around 1000rpm mark)
      shown in video:

      ...
    18. Replies
      4
      Views
      610

      Sent you a PM Trixy

      Sent you a PM Trixy
    19. Replies
      4
      Views
      610

      Anyone do aluminum welding? (GTA)

      I have a 12v VR6 aluminum intake manifold to which I need to weld a 3" piece of pipe, and a flange to the end of that pipe.
      If anyone does aluminum welding and is willing to do this I can toss you...
    20. Replies
      1
      Views
      577

      figured it out, the steering column shaft had...

      figured it out, the steering column shaft had collapsed, i extended it to the marked position:

      http://puu.sh/awJeO/2f068dd01f.jpg

      http://puu.sh/awJdd/f05639d0d5.jpg
      ...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4