Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: dunc12

    Page 1 of 6 1 2 3 4

    Search: Search took 0.61 seconds.

    1. Replies
      15
      Views
      895

      Tried a couple of different pull-up resistor...

      Tried a couple of different pull-up resistor setups and still couldn't get mega to see any rpm. No change in pulse width or rpm signal. I tried a 1k resistor in line with the 12V source and also...
    2. Replies
      15
      Views
      895

      Thanks! Will try and report back.

      Thanks! Will try and report back.
    3. Replies
      15
      Views
      895

      Thanks for the reply :thumbup: I should have...

      Thanks for the reply :thumbup:

      I should have mentioned that I'm running a V2.2 board with megasquirt 1 (MSnS extra code).

      Do I need the pull-up resistor for this setup?
    4. Replies
      15
      Views
      895

      Well, bumping this after the project has sat...

      Well, bumping this after the project has sat dormant for a little while due to school and such.

      The motor is in the car, mega is in the car and wired up, and the car is ready to fire!
      ...
    5. I can usually get them all with a variety of...

      I can usually get them all with a variety of extensions, but there's always one that I have to turn out bit by bit with a wrench.

      I would think about using new hardware when re-installing: copper...
    6. Are you removing just the manifold, or the...

      Are you removing just the manifold, or the manifold and downpipe together?

      Removing the intake will make it easier to get to all of the nuts, but you shouldn't have to move the engine at all to...
    7. Replies
      15
      Views
      895

      Slight corretion, I am getting O2 signal, but in...

      Slight corretion, I am getting O2 signal, but in a fairly narrow range. I'm assuming I just need to play with the settings and calibration. It is working though. I'll post progress as it comes....
    8. Replies
      15
      Views
      895

      Thanks for the info. I guess my plan of action at...

      Thanks for the info. I guess my plan of action at this point is to just keep building, seeing as I have sensor input from everything else (besides O2, which is RPM dependent. Might be an issue?)
      ...
    9. Replies
      15
      Views
      895

      1. Yes, I ditched megatune as soon as tunerstudio...

      1. Yes, I ditched megatune as soon as tunerstudio recognized the board instantly. Haven't touched megatune since.

      2. No, the board isn't complete. I'm following the assembly instructions on the...
    10. Replies
      15
      Views
      895

      Megasquirt Project, Attempt #1

      As the title states, I'm giving this whole megasquirt thing a go. I'll be running MS-I V2.2 on a 16V, ordered from DIYautotune. They're good guys :thumbup:
      I already have almost everything to set...
    11. Replies
      2
      Views
      334

      Yeah, I just figured this would get more exposure...

      Yeah, I just figured this would get more exposure in here than there. Will do :thumbup:
    12. Replies
      2
      Views
      334

      Megasquirt Project, Attempt #1

      As the title states, I'm giving this whole megasquirt thing a go. I'll be running MS-I V2.2 on a 16V, ordered from DIYautotune. They're good guys :thumbup:
      I already have almost everything to set...
    13. Replies
      6
      Views
      771

      Well, after switching to small bumpers and...

      Well, after switching to small bumpers and getting a buddy's rabbit back on the road, we went for a cruise and decided to line them up for some photos. Results below:
      ...
    14. Replies
      88
      Views
      12,266

      :eek: Amazing work thus far, excited to see where...

      :eek: Amazing work thus far, excited to see where this goes :thumbup:
    15. Replies
      27,019
      Views
      2,325,183

      Finally attached my small bumper clips, no more...

      Finally attached my small bumper clips, no more sagging bumpers! Still having bumper alignment issues though, maybe someone can tell me how to adjust it properly? The driver side sticks out farther...
    16. Replies
      6
      Views
      771

      And some more! Threw the summer wheels back on...

      And some more! Threw the summer wheels back on for a cruise on the sea-to-sky highway. Results below.

      http://farm3.staticflickr.com/2837/12044083554_1ce1492560_b.jpg
      ...
    17. Replies
      27,019
      Views
      2,325,183

      Accomplished many things! Swapped my front...

      Accomplished many things!

      Swapped my front mount back to solid rubber
      Finished relaying my headlights (amazing difference) :thumbup:
      Fixed my gas tank float
      Made a radio block-off plate...
    18. Replies
      6
      Views
      771

      Just a few more from a recent night-time cruise....

      Just a few more from a recent night-time cruise. Props again to xanderdeg for the photos :thumbup:

      <a href="http://www.flickr.com/photos/87234120@N04/11991543424/" title="Abbot 1 by dunc12, on...
    19. Replies
      29
      Views
      3,584

      Poll: Agreeing here, definite yes.

      Agreeing here, definite yes.
    20. Replies
      27,019
      Views
      2,325,183

      Replaced my thermostat, finally. It's been stuck...

      Replaced my thermostat, finally. It's been stuck open for a month... :banghead:
    Results 1 to 20 of 113
    Page 1 of 6 1 2 3 4