Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: xtremevdub

    Page 1 of 13 1 2 3 4

    Search: Search took 0.66 seconds.

    1. Replies
      87
      Views
      7,368

      Hey man, all that work and you are leaving that...

      Hey man, all that work and you are leaving that old radiator?
      You know those things blow up for no reason when you least expect it, right?
      Great job so far. :thumbup:
    2. :popcorn:

      :popcorn:
    3. Replies
      265
      Views
      33,664

      You could cut the hump on the aba TB no problem...

      You could cut the hump on the aba TB no problem to have the same height as the other tb. Just in case one breaks and you could use it again. :thumbup:
    4. Replies
      55
      Views
      14,173

      :popcorn:

      :popcorn:
    5. Replies
      6
      Views
      651

      you forgot this one... ...

      you forgot this one...

      http://img687.imageshack.us/img687/6688/motorx.jpg

      :P
    6. :confused:

      :confused:
    7. The intake ports are that clean cause that head...

      The intake ports are that clean cause that head was sent to the machine shop not long ago.. Good eye on the port job.
      Cams are stock 2.0 cams.. the car is getting a turbo so they should work fine...
    8. I'm running different management so the idle...

      I'm running different management so the idle valve hole got plugged a long time ago.
      So it's only clean air going into the throttle body and nothing else.
      That's why I'm thinking it may be some...
    9. Oil in the lower Intake Runners after a catch can???

      So I put a catch can on my car cause I dont like the idea of oil vapors going into my intake.. And after a couple of months, my catch can is basically empty.

      So I removed the intake manifold and...
    10. Replies
      111
      Views
      10,827

      Looks like nothing happened to the bimmer???...

      Looks like nothing happened to the bimmer??? wow.. I didnt know our cars were like toyotas
    11. Replies
      1
      Views
      160

      :thumbup:

      :thumbup:
    12. Replies
      1,094
      Views
      97,416

      I wish I would have seen it before I removed the...

      I wish I would have seen it before I removed the entire fuse box looking for melted wires.. :banghead: And I was looking for that because it died very weirdly.
      First I was running in fumes.. So I...
    13. Replies
      1
      Views
      160

      FS: Audi TT dead pedal in Miami

      Selling an Audi TT dead pedal in great condition. Only one broken tab.
      Goes perfect with the TT pedals if you have them or looks great by itself. Fits all MK4's.


      $50 SHIPPED to the lower 48...
    14. Replies
      1,094
      Views
      97,416

      Today I decided to spend some time trying to...

      Today I decided to spend some time trying to figure out why mine died about a month ago in the middle of a bridge in the pouring rain..
      after a few hours of disconnecting and inspecting every wire...
    15. See if pin 24 on your ECU throws a signal when...

      See if pin 24 on your ECU throws a signal when you open ignition. The computer turns on the fuel pump relay and from there it goes to the fuel pump.
      Could be your ECU.
      ...
    16. This is not correct.. the pump primes even if the...

      This is not correct.. the pump primes even if the car doesnt run.. Or at least is supposed to.
      To the OP, turn the ignition switch on and listen if the pump starts working for a couple of seconds....
    17. Replies
      1,094
      Views
      97,416

      You can use the tool to press it out or hammer it...

      You can use the tool to press it out or hammer it out.. I prefer the last method.

      When you modify the HF tool, you end up using the 72mm tool and making it a tad smaller.. 72mm is the same size as...
    18. Replies
      1,094
      Views
      97,416

      That method takes too many tools that you have to...

      That method takes too many tools that you have to "make" and it pushes the bearing back in by pressing the center of the bearing, which can ruin it easily. Plus it is very time consuming.
      Do you...
    19. Replies
      1,619
      Views
      513,888

      you have more pics of the motor??? that looks...

      you have more pics of the motor??? that looks great :thumbup:
    20. Replies
      5
      Views
      212

      Is for a g60, but I dont think it makes much o a...

      Is for a g60, but I dont think it makes much o a difference.
      got pics?
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4