Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: MRosier

    Page 1 of 13 1 2 3 4

    Search: Search took 0.77 seconds.

    1. Replies
      378
      Views
      53,154

      where did you acquire the green LEDs for your...

      where did you acquire the green LEDs for your autometer gauges? are they 194 wedge bulbs?
    2. Replies
      8
      Views
      461

      When I had C2 30#, my car did this (obd2) and I...

      When I had C2 30#, my car did this (obd2) and I found a few others with the same problem and no one could find a solution...I came to the conclusion its just a characteristic of the software, once I...
    3. definitely not normal, the axle should slide...

      definitely not normal, the axle should slide completely through the full length of the splines in the hub.
    4. Replies
      0
      Views
      157

      MK3 and 3.5 Top FRAME interchangeability

      Can anyone provide any input whether or not I could take a 2002 top assembly (late style with stitched rear glass) and replace the top material with an early MK3 top material and retrofit the early...
    5. Replies
      5
      Views
      292

      check the wiring at the yellow coolant sensor....

      check the wiring at the yellow coolant sensor. Mine became brittle and the insulation wore off right at the plug causing two of the wires to touch making the fans stay on with the key off.
    6. Replies
      1
      Views
      323

      I did it that way on mine with no problems :)

      I did it that way on mine with no problems :)
    7. Replies
      14
      Views
      1,178

      single chambers, GL tails, Tfti , green stitched...

      single chambers, GL tails, Tfti , green stitched goodies :thumbup::thumbup::beer:
    8. Replies
      17
      Views
      800

      Has anyone fooled with putting 3.5 Cabrio rear...

      Has anyone fooled with putting 3.5 Cabrio rear calipers onto a golf/jetta? They are aluminum like MK4. I'm curious if the brake hoses would be a direct swap to MK3.
    9. Replies
      9
      Views
      375

      The vibration damper (steel block bolted to sub...

      The vibration damper (steel block bolted to sub frame) does not have anything to do with the rubber donut on the oem passenger axle. The donut thing does not rest on the vibration damper. Bolt the...
    10. Replies
      2
      Views
      354

      Is the front bar still available?

      Is the front bar still available?
    11. dang I need these...rears too? Wish you would...

      dang I need these...rears too? Wish you would ship. I'm in MD
    12. Replies
      9
      Views
      375

      Do you still have the vibration damper bolted to...

      Do you still have the vibration damper bolted to the subframe?
    13. Replies
      9
      Views
      726

      bearings or just bolts? Crankshaft must be...

      bearings or just bolts? Crankshaft must be completely removed to do bearings. they get converted to studs instead of bolts if you replace with ARP. not something I would remove one by one like you...
    14. Replies
      17
      Views
      2,436

      Those are motor mount bolts yes, if you would of...

      Those are motor mount bolts yes, if you would of comprehended the title and/or looked at the picture you would see that the OP is looking for a motor mount bracket bolt.
    15. Replies
      1
      Views
      176

      Megan Racing front strut brace?

      I'm in the market for a front strut brace that actually works...came across one I've never seen before on ECS:...
    16. A worn valve guide will cause oil burning as it...

      A worn valve guide will cause oil burning as it will egg out the valve seal. A worn valve guide will not cause low compression however. So unless there was a valve seat problem or a damaged...
    17. Replies
      2
      Views
      215

      if there is that much play present, you should be...

      if there is that much play present, you should be able to feel if it is the inner tie rod end by placing your hand on the dust boot and simultaneously shaking the wheel side to side. I've also seen a...
    18. ttt

      ttt
    19. Also make sure there is no debris or coolant/oil...

      Also make sure there is no debris or coolant/oil down in the block holes for head bolts!
    20. hmm seems strange. I've done several fiber HG's,...

      hmm seems strange. I've done several fiber HG's, MLS with and without head spacers before and never even had a speck of seepage. Always just used scotch bright or one of those funny rubber/plastic...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4