Search Results - Vortex Media Group
Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: need_a_VR6

    Page 1 of 13 1 2 3 4

    Search: Search took 0.20 seconds.

    1. These cars are getting old enough that the...

      These cars are getting old enough that the suspect list is long, here are some things to check:

      Fuel pressure and volume (there are TWO fuel pumps!)
      Ignition switch
      Ignition coil, cap, rotor,...
    2. Go to ego menu and turn % correct to 0. Try...

      Go to ego menu and turn % correct to 0. Try again.

      Check the basics, cam timing, ignition timing, sensor readings etc
    3. Replies
      1
      Views
      151

      2008 vs 2012

      I know the earlier motors have a different head casting (no vac pump) and intake manifold (changeover valve). Other than that they are the same. I don't know offhand the exact year of those changes,...
    4. Replies
      3
      Views
      171

      That part I am unsure of. You may be able to get...

      That part I am unsure of. You may be able to get some info from the Passat guys as they use the Mk5 R32 exhaust as a retrofit.

      Pretty sure yours look like this:
      ...
    5. Completely not a problem with the mk4 gasket on a...

      Completely not a problem with the mk4 gasket on a 95. Modern mls gaskets also don't need that good a finish. You can stone grind them and it works great.
    6. Replies
      3
      Views
      171

      Its close but not quite right. May be able to be...

      Its close but not quite right. May be able to be redrilled. The mk5 r32 downpipe or aftermarket equivalent will bolt up to the 3.6 manifolds.
    7. Replies
      4
      Views
      188

      A lot of times the solder joints on the connector...

      A lot of times the solder joints on the connector crack. It can be repaired usually.
    8. Replies
      10,296
      Views
      632,685

      This is one of those things where hairs are split...

      This is one of those things where hairs are split and there are really no practical differences. Do the 1.8t iat and manifold heat soak plays a minimal part in power production
    9. I think it would work a lot better with staggered...

      I think it would work a lot better with staggered lengths and a plenum surrounding it with a single TB.
    10. I take that back, there was a Corrado with an...

      I take that back, there was a Corrado with an over the motor manifold that looked like a pair of headers. Had dual throttle bodies from what I remember. Like most "show" things probably never hit the...
    11. Replies
      4
      Views
      140

      Yeah sorry. Located in SE PA

      Yeah sorry. Located in SE PA
    12. If you go over the motor there is plenty of room...

      If you go over the motor there is plenty of room for runners and the plenum. Totally do-able, just never seen one made like that.
    13. Replies
      4
      Views
      140

      Wanted: PART of a hatch (what?)

      Ok, odd request but maybe someone has a hatch with issues and is willing to help out. I need the sheet metal that is below the 3rd brake light between the tails with the mounts for the tails and the...
    14. Replies
      2
      Views
      183

      Without using a totally different design coil,...

      Without using a totally different design coil, there is no upgrade available. That being said the stock coilpacks will light off all but the most challenging mixtures. Mtech still uses these well...
    15. Replies
      3
      Views
      370

      I may design a few adapter boards for it. Don't...

      I may design a few adapter boards for it. Don't like the bob though its faster to just solder a connector and shrink it.
    16. Replies
      116
      Views
      19,896

      Someone still has my rear shocks holding up their...

      Someone still has my rear shocks holding up their car...

      https://lh3.googleusercontent.com/-jrIWUicFYfs/VrDN7PhwPjI/AAAAAAAASEM/wBJsF0jgsKE/s640-Ic42/IMG_1909.JPG

      Waterpump mounted. You can see...
    17. Replies
      3
      Views
      187

      Still available!

      Still available!
    18. Still available!

      Still available!
    19. Still available!

      Still available!
    20. Replies
      3
      Views
      370

      Microsquirt Module for PnP Motronic

      Just a little project I put together for a customer. Needed to fit inside a stock ECU case for class rules. Needed adjustability but didn't want to break the bank.
      ...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4