Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: haf1zur

    Page 1 of 13 1 2 3 4

    Search: Search took 0.67 seconds.

    1. :)

      :)
    2. Replies
      2
      Views
      238

      Engine bay? Connected to the Reverse Gear...

      Engine bay?

      Connected to the Reverse Gear Switch?
    3. Replies
      21
      Views
      1,297

      not sure if they do them in the US but i have...

      not sure if they do them in the US

      but i have this:

      http://di1-2.shoppingshadow.com/images/pi/b4/ea/9a/103689619-260x260-0-0_Clarke+Power+Products+CLARKE+CIR24+200NM+PRO+1+2+2.jpg

      and this
      ...
    4. Replies
      28
      Views
      2,726

      G40 is the camshaft position sensor towards the...

      G40 is the camshaft position sensor towards the front of the engine

      Is it loose?

      Do you get the same error when the cable is disconnected from the connector?
    5. Replies
      12
      Views
      620

      Looks like i will be fine with these They are...

      Looks like i will be fine with these

      They are longer than the OEM stock bolts even with the nut and washer attached sitting flush

      As you can see from the two pics below:
      ...
    6. Replies
      12
      Views
      620

      Thanks Climiefish Will look into those ...

      Thanks Climiefish

      Will look into those

      Going to double check the stud lengths of the ARP ones first, dont want to spend if i dont have to

      If I dont use the washers they will sit flush, ARP...
    7. you can do them yourself, its fairly simple ...

      you can do them yourself, its fairly simple

      all you need is m12 male - female studded rose joints on each end and a metal bar

      had a company over here make them for 80 pounds for a pair
      ...
    8. Replies
      12
      Views
      620

      If i remember correctly it was ArrowPrecision i...

      If i remember correctly it was ArrowPrecision i got these off, was a while back

      Remember making sure that the 3.2 was listed before hitting the buy button

      Climiefish, is it the RWE 2002 for the...
    9. Replies
      12
      Views
      620

      As you can see in the below pic, the stud fits...

      As you can see in the below pic, the stud fits too far in and the nut is not holding the stud flush, spoke to arp and they said they dont do a kit for the 3.2 and that the one i have is for a 2.8
      ...
    10. Replies
      12
      Views
      620

      Which kit please? I have 204-5403 and it...

      Which kit please?

      I have 204-5403 and it doesn't fit by the looks of things

      Thanks
    11. Replies
      12
      Views
      620

      Main Cap Studs - What are you using?

      Hi

      What are you using for main cap studs?

      Wondering whats available

      Thanks
    12. Thread: Is this safe?

      by haf1zur
      Replies
      5
      Views
      2,472

      Arp Main Cap Bolts - Is this safe?

      Hi

      Fitted arp bolts to the main caps and noticed that the nuts dont cover the bolts flush

      Is it safe to run like this or should i remove the washers?
      ...
    13. Thread: Broken Bits

      by haf1zur
      Replies
      3
      Views
      1,257

      Just back from the machine shop The piston...

      Just back from the machine shop

      The piston does not come close to that part so was told its all good

      about and inch and half above that i can see the marks from the bottom of the piston rings
      ...
    14. Thread: Broken Bits

      by haf1zur
      Replies
      3
      Views
      1,257

      Not a valve, i think the the rods hit the side of...

      Not a valve, i think the the rods hit the side of the block at the bottom of the piston champer

      two chips missing from the area circled below
      ...
    15. :)

      :)
    16. Thread: Broken Bits

      by haf1zur
      Replies
      3
      Views
      1,257

      Broken Bits

      Hi

      Was taking apart my spare block and found this:

      http://img6.imageshack.us/img6/4032/longblock001.jpg

      http://img832.imageshack.us/img832/6411/longblock002.jpg

      Two bits of broken metal...
    17. :)

      :)
    18. Thanks everyone Saves me money not doing it ...

      Thanks everyone

      Saves me money not doing it

      So just the piston tops, valves then
    19. Ceramic Coating Cylinder Block - Advice please

      Hi

      I have a 2004 Golf R32 3.2 VR6 Engine

      I am wanting to get my cylinder block ceramic coated, it has been bored and honed for oversized pistons

      I wanted to get it coated, but was wondering...
    20. Does it still do that if you take the window all...

      Does it still do that if you take the window all the way up and then down by holding the button pressed?

      It sometimes happens but after a couple of closures it starts to work again, i think its a...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4