Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: ChrisAudi80

    Page 1 of 2 1 2

    Search: Search took 0.58 seconds.

    1. BUMP

      BUMP
    2. Replies
      6
      Views
      358

      up up yo

      up up yo
    3. Replies
      154
      Views
      106,559

      Had this swap done 2 months ago. I had a 2.0E...

      Had this swap done 2 months ago.

      I had a 2.0E auto fwd car. I went to quattro manual. Not sure which mounts were used. It was a lot of work though.
      ...
    4. FS: VEMS ECU with finished harness for 1.8T

      I bought this VEMS ECU with harness, boost controller, WBO2 sensor, injectors and new coils (06A) a few months ago. Some of you might have seen that ad.

      It originally came from bulldoser62 who...
    5. Replies
      6
      Views
      358

      bump

      bump
    6. Replies
      6
      Views
      358

      Can't upload any pictures. Check this topic:...

      Can't upload any pictures. Check this topic:
      http://theprojectpad.com/viewtopic.php?f=7&t=1305&p=62119#p62119
    7. Replies
      6
      Views
      358

      up yo

      up yo
    8. Replies
      6
      Views
      358

      bump:wave:

      bump:wave:
    9. Replies
      6
      Views
      358

      FS: VEMS ECU with harness for 1.8T

      I bought this VEMS ECU with harness, boost controller, WBO2 sensor, injectors and new coils (06A) a few months ago. Some of you might have seen that ad.

      It originally came from bulldoser62 who...
    10. I am glad you did exhume this. I did find a...

      I am glad you did exhume this.

      I did find a way to get rid of the AFM. I put a piggyback ECU in my B4 Audi 80 with a 2.0E Digi-II with autotrans. This piggyback can be run in AFM elimination mode....
    11. SOLD!!

      SOLD!!
    12. YGPM!

      YGPM!
    13. Replies
      154
      Views
      106,559

      Yes. Read the OP again.

      Yes. Read the OP again.
    14. Nobody?

      Nobody?
    15. VW097 (01N) transmission; power/torque capacity?

      I have been searching a lot, trying to find out what the power and/or torque handling capacity is for the 097/01N auto trans. I know they were also used for the 2.8 V6, so should be able to handle...
    16. I know this is an old thread, but I thought maybe...

      I know this is an old thread, but I thought maybe one of these kits could be useful:
      http://www.splitsec.com/products/mafkits/MAFkits2.htm

      I read the early posts and noted the comments about CFM...
    17. Replies
      48
      Views
      5,117

      Just run distilled water and maybe water wetter....

      Just run distilled water and maybe water wetter. It would be good if you could have a bleed point on top of one of your AWIC end tank, which ever end tank is highest. The reservoir will bleed just by...
    18. Replies
      48
      Views
      5,117

      From what I have read so far of successful AWIC...

      From what I have read so far of successful AWIC setups, that sounds good. See if you can put a little bleed valve at the highest point of the system.
    19. Replies
      3
      Views
      1,629

      You know what I wanted to post, but after...

      You know what I wanted to post, but after re-reading the forum rules, could not.
      I was referring to my own post which I edited.

      Not referring to your OP.
    20. Replies
      48
      Views
      5,117

      You really need a bleed valve at the highest...

      You really need a bleed valve at the highest point of the system. That might be it.
      Others have used the Cobra pump with success.
      Any reservoir needs to be away from the heat of the engine bay.
    Results 1 to 20 of 29
    Page 1 of 2 1 2