Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: zoidmk5

    Page 1 of 13 1 2 3 4

    Search: Search took 0.77 seconds.

    1. Thread: A little build

      by zoidmk5
      Replies
      154
      Views
      49,066

      great to see an update on this after all this...

      great to see an update on this after all this time. really anxious to finally see this thing in person hopefully in the near future
    2. Replies
      3
      Views
      253

      have you scanned the car to find any codes?

      have you scanned the car to find any codes?
    3. Replies
      13
      Views
      448

      could be a possibility. the increased cylinder...

      could be a possibility. the increased cylinder pressure and fuel delivery at high RPM's with bad seals could very well cause the problem. I would still like to see the logs. so either fix or replace...
    4. wrong forum. grogory will go ahead and transfer...

      wrong forum. grogory will go ahead and transfer this over to the MK2 folder
    5. Replies
      3
      Views
      505

      you can probably start out with a cheap kit like...

      you can probably start out with a cheap kit like that, and swap out the crappy turbo for a PTE or COMP unit, as well as the wastegate. you have lots of options. you can easily get that kind of power...
    6. Thread: T3 50Trim

      by zoidmk5
      Replies
      5
      Views
      411

      this is essentially what you will have when all...

      this is essentially what you will have when all is said and done. makes pretty respectable power, but is pushing the upper limit of your rods. there is a thread in the 1.8T forum that is about...
    7. your going to spin like a mad man with that kind...

      your going to spin like a mad man with that kind of tire pressure...don't look at the wheel size in your equation, look at the overall height of the tire, a that is your actual rotational mass
    8. Replies
      3
      Views
      191

      as .ANT said, 06A block, 02J trans. just find...

      as .ANT said, 06A block, 02J trans. just find yourself another 4 cyl 02J trans and you'll be good to go. keep in mind, the 5 speed used in the MKIV 12V VR6 was also an 02J, but the bell housing is...
    9. depends on the wheel offset and front end ride...

      depends on the wheel offset and front end ride height
    10. Thread: SoMD Dubs

      by zoidmk5
      Replies
      45,922
      Views
      1,105,359

      sounds good

      sounds good
    11. Thread: SoMD Dubs

      by zoidmk5
      Replies
      45,922
      Views
      1,105,359

      I'm down

      I'm down
    12. damn it Mike, when I suggest you for something, I...

      damn it Mike, when I suggest you for something, I expect a sincerely confident answer...disappointed

      I do however agree that a drag radial may cause more harm than good. if this is a tire that you...
    13. make sure you have continuity on the signal wire...

      make sure you have continuity on the signal wire from the individual injectors to the ECU

      how long has it been sitting? sending them out to be cleaned and flow tested might also be an option
    14. Thread: 06 A3 Vag Com

      by zoidmk5
      Replies
      2
      Views
      220

      go to Autozone or Advance Auto Parts and have...

      go to Autozone or Advance Auto Parts and have them scan it for free. they will print you out a receipt that has your codes all spelled out. when you figure out the code and fix it, disconnect your...
    15. Thread: 1.8t swap mk3

      by zoidmk5
      Replies
      8
      Views
      516

      call them right now, they're open

      call them right now, they're open
    16. most of the hardcore drag racers actually...

      most of the hardcore drag racers actually downgraded their brakes to the 10.1" from the MKIII so that they can actually run 14" if not 13"

      I assume that this car is still street driven, so I would...
    17. Thread: engine problem

      by zoidmk5
      Replies
      8
      Views
      434

      scan it and see what it says, that's about all we...

      scan it and see what it says, that's about all we can go by
    18. Thread: 1.8t swap mk3

      by zoidmk5
      Replies
      8
      Views
      516

      you also need to remember that in Norway, your 6...

      you also need to remember that in Norway, your 6 hours ahead of us on the East Coast in the U.S., which is where BFI is, so you need to make sure that when you call them, it is during their working...
    19. Thread: 1.8t swap mk3

      by zoidmk5
      Replies
      8
      Views
      516

      granted I did my MK3 1.8T swap using standalone,...

      granted I did my MK3 1.8T swap using standalone, I know that the BFI kit was made so that it is plug and play with ABA harness and ECU. I would trace the wires and compare to the fuse block diagram...
    20. Thread: SoMD Dubs

      by zoidmk5
      Replies
      45,922
      Views
      1,105,359

      what size and material? I can typically get...

      what size and material? I can typically get whatever mandrel bent pieces within a day or two
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4