Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: Enter the chicken

    Page 1 of 2 1 2

    Search: Search took 0.25 seconds.

    1. MS1 standalone questions, give me your 2cents!

      Have you looked in the SEM, ITB forum?
    2. AMS Manifold

      Old post, however I thought that I would still try. Still around?
    3. Timing belts

      Will you be carrying the ABF timing belt?
    4. Replies
      3
      Views
      517

      When I did my homemade harness I found the same...

      When I did my homemade harness I found the same problems. What I found was that I forgot to wire into the fuel pump circuit. So my pump would prime but the engine would die after start up. Also your...
    5. Replies
      643
      Views
      71,510

      I see that your mount is different. Thanks for...

      I see that your mount is different. Thanks for the replies. Are you going with Diesel Geek shift linkage?
    6. Replies
      643
      Views
      71,510

      I was wondering, can you remove the switch from...

      I was wondering, can you remove the switch from it's original spot and use one of those other plugs/bolts that are next to it? Then it would probably fit with the factory plug.
    7. Replies
      643
      Views
      71,510

      Sorry, I meant to ask about the trans mount on...

      Sorry, I meant to ask about the trans mount on driver's side to reverse switch clearance. As I have the German made 02J/02A to mk1 mounts which has a provision for cable clutch actuation. Which...
    8. Replies
      643
      Views
      71,510

      How are you dealing with the reverse switch?

      How are you dealing with the reverse switch?
    9. Replies
      10
      Views
      962

      I'm putting together an 02J in my Rabbit with the...

      I'm putting together an 02J in my Rabbit with the German made mk4 to mk1 mounts and cable clutch actuator, I was wondering what you guys did about the reverse switch hitting the mount. Most people...
    10. Replies
      222
      Views
      80,625

      cam position sensor

      Hi followed your thread and one thing that I wanted to do as well is make a cam position sensor from my 16v distributor. After looking around for quite some time nowI found something that you might...
    11. Intermediate shaft

      Happy new year Fred! Just wondering what you did with the 9A intermediate shaft as I am building an ABA 16V turbo and am wondering if I should have it machined smooth or just leave it. I am also...
    12. Replies
      16
      Views
      1,356

      I have the old 2 piece Oettinger oil pan/sump...

      I have the old 2 piece Oettinger oil pan/sump where the upper piece has a built in windage tray. Was thinking I could tap the upper just below the windage tray but these are rare. However I think it...
    13. Replies
      16
      Views
      1,356

      Tapping ABA block for oil return

      I was thinking of using one of the tapped holes down at the bottom of the block where the webbing is. Do you think that will interfere with the axle?
    14. Leakage

      Maybe take a look at the passenger side drain from the rain tray to engine compartment. There is a rubber grommet there that gets clogged with debris. Then the water backs up and comes through the...
    15. Replies
      3
      Views
      867

      Help with VR6

      You should talk with your local wrecking yard. They have parts cross referencing that will tell you what you can swap
    16. Wheel hubs

      I have reused mk1 through mk4 hubs and what I found was that the mk1 hubs were the easiest to reuse. Having said that...you still have to make sure that your hubs are still good to use! Light sanding...
    17. Power Steering - Safe to say that it is indeed your rack!

      Sorry to hear this as I went through the same thing:confused:As your car is an early one I would suggest putting in an R32 rack. With all new stretch bolts for subframe and rack to subframe. Flip the...
    18. Sway bar on MkIV with TT/R32 spindle conversion

      Was wondering this same question as my MkIV spindle to tie rod hole is damaged. Not sure about the placement of the ball joints between MkIV and R32 but can't you just use your MkIV control arms and...
    19. mounts

      Hey Fred where did you get your mounts? Thanx Craig
    20. How does the eurovan cable attach to the mount?

      How does the eurovan cable attach to the mount?
    Results 1 to 20 of 32
    Page 1 of 2 1 2