Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: vtraudt

    Page 1 of 13 1 2 3 4

    Search: Search took 0.61 seconds.

    1. i don't recall anymore, but I did the same thing....

      i don't recall anymore, but I did the same thing. Inside is a darn "washer lock" that fell down. Bitch to seat that right again, since 'runs' inside a U shaped notch on the lock to pull it in. I...
    2. Replies
      4
      Views
      122

      Must be a very narrow zip tie to fit into the...

      Must be a very narrow zip tie to fit into the slot/groove, which is only 2mm wide (or so, the wire diameter of the clip).

      Maybe I try another solution I have used in the past (plastic "C" clips...
    3. Replies
      4
      Views
      122

      I don't see how a zip tie would secure the...

      I don't see how a zip tie would secure the plastic connector on the metal pipe?
      You would need to create an axial force to keep 'pulling' it onto the pipe (unlike with rubber hoses, where you can in...
    4. Replies
      4
      Views
      122

      2.7T heater and coolant hose "C" clips

      I need the open metal "C" clips for the heater and coolant hoses for the 2.7T:

      - rear of engine to heater core hoses (2 smaller ones)
      - front of engine to radiator (2 larger ones).

      Mine are...
    5. Replies
      15
      Views
      5,906

      Have engine (previous owner, AEB) with Mahle...

      Have engine (previous owner, AEB) with Mahle pistons. Want to put new rings on. Can someone chime in?
    6. Replies
      19
      Views
      3,904

      Can someone post good photos of the front/back of...

      Can someone post good photos of the front/back of the clip? I will try if I can add it to my stock.
      www.RegulatorFix.com
    7. Replies
      212
      Views
      64,458

      12V or 24V heads

      Any thoughts on 12V vs. 24V heads?
    8. Replies
      212
      Views
      64,458

      Stock ECU flashed?

      Why ECU removal? Sent in for flash?
      How is boost control done? External wastegate?
      Who did the ECU conversion/tune from NA to boosted?
    9. Replies
      19
      Views
      1,889

      OP not a single reply. Presumed dead thread.

      OP not a single reply.
      Presumed dead thread.
    10. Replies
      8
      Views
      313

      Yeah. Either 1000cc (but still 'trickling'...

      Yeah. Either 1000cc (but still 'trickling' instead of spraying at high boost (low effective pressure) or return style. Darn. More work. So easy on my ATW and APB.
      But then again: just climbed out...
    11. Replies
      8
      Views
      313

      All assumptions seem valid. 750cc at 3 bar:...

      All assumptions seem valid.

      750cc at 3 bar: check

      4 bar base pressure: check

      2 bar boost (28 psi): check for calculation

      Net pressure: 2 bar: check.
    12. Replies
      8
      Views
      313

      Oh, you want to get linear raising rate fuel...

      Oh, you want to get linear raising rate fuel pressure pressure regulator function (vs. constant pressure in case of the B6 returnless system).
      I don't see that as a must have; quite a bit of work;...
    13. Replies
      8
      Views
      313

      Haven't thought of that. Why is return required?...

      Haven't thought of that. Why is return required?
      Arnold, the air bag guys?

      I remember seeing a Bosch 044 drop in solution (034?), but cost prohibitive (not sure if it was for B6 or Allroad).
    14. Replies
      8
      Views
      313

      B6 1.8t amb - e85

      Aside from the required additional volume/flow (injectors, pump) and tune, what other components (gaskets, hoses, O rings, lines, filters, etc.) need to be changed when converting to E85 on B6 (here:...
    15. Replies
      27
      Views
      4,987

      Possible to put AEB (from 058) head with 11mm...

      Possible to put AEB (from 058) head with 11mm head bolts on 06A block (10mm head bolts)? Washer/spacer needed under 10mm bolt heads?
    16. I have $150 shipped to MI 48114.

      I have $150 shipped to MI 48114.
    17. Replies
      13
      Views
      950

      Miles on the car? Miles since build/rebuild?...

      Miles on the car?
      Miles since build/rebuild?
      Interior photos?
      Cloth seats?
    18. Replies
      13
      Views
      950

      motor, block, heads

      Stock (used: miles?) exhaust valves or upgraded (solid)?
      Stock (used: miles?) valve springs or upgraded?
      Miles on the heads since rebuild (assume complete rebuild was done with valve job, guides,...
    19. IE rods 144x20 new

      I have $280 shipped to MI
    20. Replies
      0
      Views
      118

      FS: EGR Kombivalve 1.8T

      Removed from well running 100k AMB engine (2003) with no codes.
      $60 shipped (conti US).
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4